, ,

Attending To Power Harmonics With Fluke Tools

Newton’s third law says that for every action, there is an equal and opposite reaction. We are reaping the consequences of the actions of the generation before us. Harmonics has been around for a considerable amount since the introduction of electronic drives for motors, fans, and pumps. Let’s learn more about harmonics and how to address this problem.

What is Harmonics?

Harmonics are the side effects of electronics. These are distortions in the normal electrical current waveform transmitted by non-linear loads. When harmonics are combined with fundamental frequency, this creates distortion in the waveform which causes an adverse effect on your electrical equipment and power lines. Harmonics can be detected by checking these:

1. Load Inventory

2. Transformer Heat Check

3. Transformer secondary current

4. Sub-panel neutral current check

5. Receptacle neutral-to-ground voltage check

Switch-mode power can be seen on electrical devices such as photocopiers, personal computers, laser printers, fax machines, and battery chargers. They are commonly used in supply design because of their ability to supply a fixed voltage output continuously.

Dangers of Power Harmonics

Dealing with electricity can be hard at times because of the dangers it carries with it. There are power systems that can handle a certain level of harmonic currents. But if there is a significant load more than the power system can hold, it can cause errors in communication, overheating, and hardware damage. Here is some hardware damage that can happen:

  • Overheating of electrical distribution equipment, cable, transformers, standby generators, etc.
  • Metering errors
  • Generator failures
  • False tripping of branch circuit breakers
  • Lower system power factor resulting in penalties on monthly utility bills
  • Crest factors and related problems
  • Fires in wiring and distribution systems
  • High voltages and circulating currents caused by harmonic resonance

But these circumstances can be avoided with proper maintenance using dependable maintenance tools.

Solving Power Harmonics with Fluke Tools

To solve your harmonics problem, you can turn to Fluke! Fluke has reliable tools for measuring true-RMS and peak values of the wave shape.

Fluke 87V MAX True-rms Digital Multimeter

It measures true-RMS ac voltage and current of non-linear signals from electrically noisy equipment and variable frequency motor drives or VFDs. This trusted multimeter can work with you in dry, dusty, dark, or wet environments for long days. This rugged multimeter can survive drops up to 13 feet. It provides accurate measurements even within an extreme temperature that ranges from -40 degrees Celsius to +55 degrees Celsius. With a large display of digits, white backlight, and backlit keypad buttons, you won’t have a hard time reading the measurements! Use it for 800 hours

Fluke 87V MAX true-RMS Digital Multimeter. Photo from Fluke.com

Fluke 175 True-rms Digital Multimeter

This multimeter measures the frequency, capacitance, resistance, continuity, and diode. By measuring these, you are tracing the root of the problem. Its Display Hold and Auto Hold helps you capture important events or measurements. The data input is protected by IEN61010-1 CAT IV 600 or V/CAT III 1000 V. UL, CASA, and TUV.

Fluke 175 true-rms Digital Multimeter. Photo Fluke.com

Fluke 289 True-rms Data Logging Multimeter

It is a high-performance industrial logging multimeter of the next generation. This is Fluke Connect compatible which means you can monitor your readings even from afar using iOS or Android smart devices through the Fluke Connect app. It records and saves readings in real-time with a time stamp! It can also save up to 15,000 recorded readings. You can easily hang it because of its magnetic hanger. Thus, giving more room for your hands to move around.

Fluke 289 true-rms Data Logging Multimeter. Photo from Fluke.com

Fluke 381 Remote Display True-rms AC/DC Clamp Meter with iFlex

With a 6 feet cord, you can take readings even when you are in tight spaces. You won’t think about disorganized wires anymore! This ergonomic clamp meter has proprietary inrush measurement technology to filter noise and capture starting currents. The iFLEX Flexible Current Probe has expanded measurement range up to 2500 A AC.

Fluke 381 Remote Display True-rms AC/DC Clamp Meter with iFlex. Photo from Fluke.com

Get your Fluke tools through an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools within Metro Manila.

Sources:

https://www.fluke.com/en-us/learn/blog/power-quality/troubleshooting-power-harmonics

https://www.newark.com/pdfs/techarticles/eaton/Eaton_Technical_Articles/UPS_Training/Powerware_Training/HarmonicsInYourElecSystem.pdf

https://www.electronics-tutorials.ws/accircuits/harmonics.html

https://www.electronics-tutorials.ws/power/switch-mode-power-supply.html

https://www.fluke.com/en-us/product/electrical-testing/digital-multimeters/87v-max

https://www.fluke.com/en-us/product/electrical-testing/digital-multimeters/fluke-175

https://www.fluke.com/en-us/product/electrical-testing/digital-multimeters/fluke-289

https://www.fluke.com/en-us/product/electrical-testing/clamp-meters/fluke-381

Read more

Best Fluke Tools For Power Monitoring

Electricity is inarguably one of the most important energy forms in the world. From bulbs to phones, to computers, to cars, electricity is needed to keep them going. However, electricity can be very dangerous when mishandled and not properly stored. Regular power monitoring is necessary to keep everyone safe from any risk an electrical malfunction may pose.

What is Power Monitoring?

Power Monitoring is the process of measuring power consumption for energy-saving purposes. It is essential in preventing your devices from malfunctioning. It also minimizes the risk of encountering an event that is potentially life-threatening. Accurate and regular power monitoring can be achieved by using the best Fluke power monitors, sensors, and meters.

Benefits of Power Monitoring Using Fluke

1) Identify defects early on.

As they say, prevention is better than cure. It also applies to our devices. Early problem detection gives us time to prepare and mitigate the potential large-scale damage it could lead to.

2) Increase the life of the equipment.

Understanding the capacity of equipment will help the operators create an accurate load profile for every piece of equipment and proactively manage and allocate energy load. This helps in utilizing the equipment to reach its highest level of performance while avoiding overloading.

3) Save time and money.

These two are commodities no one wants to waste. In businesses, when you misuse time, you are also wasting money! These essential commodities are greatly affected once a business encounters a problem in power consumption and management. Instead of waiting for your equipment to break down and your business to have downtime, it is wiser to invest in power monitoring systems.

4) Increase profit.

Cutting operation costs will increase the profit of the business. Instead of experiencing downtime, focus on having reliable energy and power management system that will help grow your business faster.

5) Ensure personnel safety.

It is equally important to keep businesses running. Taking care of them is investing in the future of the business. Faulty equipment poses more danger to the operators. Power monitoring helps in making sure that there are no irregularities in the processes and that your business won’t blow up in ways you wouldn’t want to.

Best Fluke tools for Power Monitoring

Since electricity is invisible, instruments are the only way to measure it. However, it can be dangerous to measure that’s why you need reliable power monitoring tools. Are you looking for one? Fluke is known to deliver excellent maintenance needs for our devices! Look at the list of Fluke tools best for power monitoring.

Fluke 3540 FC Three Phase Power Monitor and Condition Kit

Real-time monitoring of historical power variable data and other electrical variable fluctuations can be done by this Fluke device wirelessly. It has internal storage enough for 1 week worth of data. It allows users to visually analyze data with software trending, graphing, and timeboxing.

Fluke 3540 FC Three Phase Power Monitor and Condition Kit. Photo from Fluke.com

Fluke 1734 Three Phase Electrical Energy Power Logger

Receiving the highest safety rating in the industry, this Fluke device helps you identify the source of electrical energy waste and overloaded circuits. This builds an image of energy usage which can be used in reducing energy waste and making important decisions regarding power consumption.

Fluke 1734 Three Phase Electrical Energy Power Logger. Photo from Fluke.com

Fluke 1748 Three Phase Power Quality Logger

Accurately measure harmonics and interharmonics of voltage and current with this Fluke tool. You can export data in PQDIF or NeQual compatible through a third party software installed in Fluke 1748 Power Logger. Also, this compact power logger that is compliant with international power quality standards and combined with Energy Analyze Software is able to analyze power quality with waveform data to help identify the root of all disruptions.

Fluke 1748 Three Phase Power Quality Logger. Photo from Fluke.com

Get your Fluke tools through an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools within Metro Manila. Get to know more about these products: https://presidium.ph/shop/?wlfilter=1&product_cat=fluke-power-quality-analyzers.

Sources

https://www.fluke.com/en/products/condition-monitoring/power

https://www.fluke.com/en-ph/product/electrical-testing/power-quality/1742-1746-1748

https://www.fluke.com/en-ph/product/electrical-testing/power-quality/1732-1734

https://www.fluke.com/en/product/condition-monitoring/power/3540-power-monitor-sensor

http://hoveyelectric.com/hovey-electric-power-blog/bid/70348/What-Is-A-Power-Monitoring-System

https://www.automationworld.com/home/blog/13318206/5-reasons-to-consider-a-power-monitoring-system

https://www.vertiv.com/en-asia/about/news-and-insights/articles/educational-articles/what-is-power-monitoring-and-why-does-it-matter/

Read more

How To Deal with Faulty Electrical Circuits?

how-to-deal-with-faulty-electrical-circuits

Electrical circuits are the main foundation for transmitting electric currents. To give you a brief background, an electrical circuit is a device that gives energy to charged particles constituting the current. These are one of the main parts of every device, generators, lamps, electric motors, computers, etc. Think of it this way, without electrical circuits, your electrical devices will never power up. That’s why it’s also essential to always protect them and care for them.

How do we protect electrical circuits?

A car cannot run without its batteries, and motors cannot work without their electrical circuits. So, like any vital part of electric equipment, they also need extra care, but the question is, how do we do that? There are a number of things that we can consider to protect our electrical circuits. Here are some of them according to Elprocus.

  • Fuse
  • Circuit Breaker
  • PolySwitch
  • RCCB
  • Metal Oxide Varistor
  • Inrush Current Limiter
  • Gas Discharge Tube
  • Spark Gap
  • Lightning Arrester

These are some of the things that can protect your electrical circuits to ensure that there are no faults plaguing their systems.

What happens if you have defective electrical circuits?

When this happens, you’ll know a hundred percent as your device or any electrical device for that matter, will not function. As we’ve mentioned above, the main purpose of electrical circuits is to distribute power to your motors. If they are somehow damaged, then expect possible downtimes. Worst case scenario? Faulty electrical circuits may also be dangerous to people nearby.

Defective electrical circuits are prone to damaging insulation, conductors, and equipment, and they are also prone to overheating. In such cases that faulty electrical circuits are not dealt with immediately, they can also cause fires, explosions, arc flashes, and arc blasts. These are one of the most dangerous scenarios that personnel can ever encounter.

Staying safe with the use of Fluke tools.

You can never see faults coming with the use of your naked eyes for the simple reason that it’s impossible! Luckily, Fluke tools can make the impossible, possible with their state-of-the-art maintenance tools. If you want to prevent these faults from happening, you might want to consider using the best-performing Fluke tools.

The Fluke Power Quality Analyzers can do wonders in detecting faulty electronic wiring that might harm your devices in the long run. And yes, it can also be an efficient tool in determining faulty electrical circuits. These tools can…

  • Calculate mechanical power and efficiency without mechanical sensors.
  • Measure electrical power parameters such as voltage, current, power, apparent power, power factor, harmonic distortion, and unbalance.
  • Identify power quality issues such as dips, swells, transients, harmonics, and unbalance.
  • Includes full power quality and electrical energy analyzer functionality
  • Highest safety rating in the industry; 1000 V CAT III / 600 V CAT IV

This is just a jist of the wonders that a Fluke Power Quality Analyzer possesses. But, the best way to deal with faulty electric circuits is to identify them early on rather than waiting for some malfunction to happen to your machines. Remember, prevention is better than cure (especially when you’re dealing with expensive electronic devices!).

Get your Fluke tools through an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

Read more
, , , , , ,

Maintenance Management is Keeping the World Up and Running (Here’s Why!)

maintenance-management-is-keeping-the-world-up-and-running

Going the extra mile to make sure your machines and devices are running smoothly can reap rewards in the long run. Many don’t know it, but maintenance management is a key factor in helping keep the industry up and operating. Without daily maintenance checks, a lot of machines and devices may be susceptible to faults and other malfunctions. This alone might negatively impact the productivity of workers and put a wedge on their day-to-day processes.

Just imagine if important assets suddenly shut down. Take the internet as an example. Nowadays, if your internet provider experiences any hiccups, a whole population is affected by it, with their work, school, entertainment, and a lot of other things. It’s quite obvious that people hate experiencing downtimes.

This also applies to valuable assets. Unwanted machine/device breakdowns are unforgivable especially if you need to meet certain schedules or if the machine on hand is responsible for providing power. Technically, this only highlights how important maintenance management is especially if we’re living in a machine-dependent economy. So, let’s go in-depth into just how maintenance management keeps the world up and running and how we benefit from it.

Why everyone should practice maintenance management.

Maintenance management deals with caring about the performance of every industrial tool, device, or machine. Remember, no matter how high-end your device is, it will always be susceptible to faults. Having maintenance management in your protocols can not only help with machine health but it can also be of advantage to the people working with the machines.

Having maintenance management can benefit you in these ways:

  • Longevity of the machine/device – If you do daily maintenance checks, you can easily spot possible faults that might occur. This will also save you from costly repairs.
  • It will keep the workplace a healthier environment – A well-conditioned machine keeps the workers around it more confident and assured that there won’t be any unwanted surprises.
  • Improves efficiency – if your tools are well-maintained, this will allow them to be more efficient and reliable. Accurate data and such can be expected from them.
  • Will be cost efficient – If your tools are working well, then there’s no use to spend on replacements. Whereas when you’re handling a machine that’s practically breaking down, then expect a lot of costly repairs to be made.

How efficient Fluke tools are for maintenance management?

We’re talking about the best of the best. Fluke tools are the most reliable tools for maintenance. Professionals, men, and women who work in the maintenance field prefer to have Fluke tools by their sides when doing maintenance rounds. Why? These tools aren’t just ahead of their time, but they also ensure every worker’s safety on the field. Here are the top reasons why you should have fluke tools with you during maintenance management…

  • They allow you to take measurements from afar so you don’t have to risk your safety by having close proximity to malfunctioning machines or devices.
  • Fluke can see what the naked eye cannot – they can spot possible faults that may occur.
  • These tools can also give a diagnosis of what you should do once a fault is spotted.
  • They can give and send real-time results.
  • Some Fluke features 2 or more functions in one. 
  • They encourage wireless testing.
  • Fluke instruments help to eradicate the drastic costs attributed to manual errors.

The best maintenance practice you can apply?

Do them as often as you can. If you have reliable Fluke tools by your side, why not test and test your equipment and machines as often as you can? The key to working closely with sensitive (but important) assets is to never be complacent with them. Usually, the best assets are also the costliest ones, and Fluke corporation understands this dilemma. Therefore, they built the best tools for the job.

So, as much as possible, the best maintenance management practice that is applicable anywhere and everywhere is to always evaluate your equipment are often as possible. Therefore, most maintenance men and women on the job roam around with a device in hand. Trust us when we say you will rarely see one without a testing tool with them. This is because most Fluke tools are not even that big that it becomes a nuisance to bring along. Most of them fit right in your pocket! So yes, they are not only dependable, but they are best for hand carry tools.

Going back… So how does maintenance management keep the world up and running again?

By simply taking care of the machines and equipment that makes the world go round of course! One of the main goals of maintenance management is to make sure that everything is working in its tippy-top condition. Living in a machine-generated world, this process speaks of significant importance every day. Add in Fluke tools in the picture, and we are pretty sure that things can last a bit longer.

Get your Fluke tools through an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You are in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

Read more
, ,

Top 3 Tools for Electrical Safety Testing

top-3-tools-for-electrical-safety-testing

You do not need a lot of tools and devices by your side with false promises of safety. Fluke tools are a pioneer in the industry because of their proven and tested ways to ensure worker safety during risky operations. When you are frequently exposed to dangerous electric materials and machines, these are the ideal tools for you to take. These three tools are the holy grail of ensuring safety and security in every operation.

What type of tool can ensure safety and security?

The type of tool that you want with you all the time are tools that can let you measure without any sort of contact. As much as possible, the safest way to do maintenance and test checks is within a safe distance. Insulated tools, PPE, and rubber soles can only do so much when you are up against powerful arc flashes and a faulty machine that can seriously damage your body.

Besides having a tool that can efficiently measure from afar, you also need a device that can accurately give you results. Therefore, Fluke tools are the ideal tools for the job. Fluke tools can give you the duality of safely testing faulty equipment and electric material within a safe distance, and at the same time, can give you an accurate and timely diagnosis.

The top three tools that can guarantee safe electrical testing…

As we have mentioned, you do not need a lot of tools to take with you to guarantee safety, you just need to take the right ones. These top three tools can give you electrical safety that is even better than bringing a whole toolbox with you. Considered the big three Fluke tools, the non-contact voltage testers, electrical testers, and digital multimeters will undoubtedly make every difference.

1) Fluke Non-Contact Voltage Tester…

This is a handy tool that is small enough to fit in your pockets. Its main function is detecting the presence of voltage with failed or malfunctioning assets. So, if ever you encounter one, the best tool that can give you the most accurate results is a non-contact voltage tester.

These tools can sense even the smallest amount of voltage current. The built-in sensor at the tip of the device lights up red (and waits for it to beep) this indicates that voltage is present in the material. What is great with this tool is you do not even need contact for it to work, and that alone is added safety for all workers already.

But beware, according to an official Fluke source, non-contact voltage testers can give a false negative indication (meaning it does not light up) when these instances occur…

  • The insulated test point touches grounded metal.
  • The cable being evaluated is partially buried.
  • The user is isolated from the ground.
  • It is used inside a metal enclosure.
  • Proximity testers also will not detect the presence of voltage through the shield on the shielded cable. To better understand why proximity testers, have these limitations, read the Fluke application note on the subject, “Understanding capacitive voltage sensors.” The key word is “proximity.”

2) Fluke Digital Multimeter

A great weapon of choice when you are evaluating any kind of electricity either for faults or simply doing maintenance rounds. These tools can multitask a lot and get plenty of testing done with just one device! Its testing capabilities do not just focus on one but feel free to evaluate voltmeters, ammeters, and ohmmeters as well.

Multimeters fall into one of a handful of categories:

  • General-purpose (aka Testers)
  • Standard
  • Advanced
  • Compact
  • Wireless

3) Fluke Vibration Testers

Every maintenance professional takes pride in having a Fluke Vibration Tester. Already tagged as the best and most advanced troubleshooting tool for mechanical maintenance. The device uses a special diagnosis technology that helps you immediately identify mechanical faults and prevent downtime and drastic measures to occur.

This device lets you…

  • Quickly analyze machine health.
  • Let us observe the severity of the faults.
  • It features enhanced reporting.
  • Gives you suggestions to solve the current machine situation.
  • Let us address critical problems in real-time.

Get your Fluke tools through an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You are in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools within Metro Manila.

Read more

Evaluating Humidity Using Fluke Tools

evaluating-humidity-using-fluke-tools

Humidity is terrible for your tools and equipment. To give you a brief idea, humidity is simply known as “warm air” since it pertains to the amount of water vapor in the air. If there is a lot of water vapor in the air, the humidity will be high. And certainly, with most tools and equipment, it is in their nature to have lower performance under such circumstances. Going back, this is where evaluating humidity comes in. Exposing your tools to too much humidity may damage them completely. Therefore, temperatures are set in factories and in some facilities. Therefore, having your room humidity in check can benefit your tools in terms of caring for them.

Do not forget to use Fluke tools!

But first, what better tool to evaluate humidity than the rugged Fluke tool itself? Fluke tools are one of the most trusted test devices in the industrial field. These tools can accurately give you data to let you determine machine faults with a simple click of buttons. More than that, it can also give workers the best possible protection from dangers by letting them measure within a distance. Convenient, right?

How humidity can damage tools.

Humidity can cause several devices to quickly be susceptible to faults. Humidity can encourage tools to condense and corrode on metallic parts of your rotating machines and devices. Depending on the placement of your tools, dust can also be a harmful factor when you plan to keep your tools in shape. Plus, humidity, leaves the air thick and hot. Even people do not enjoy being in humid places, what more for our tools and devices?

Other than that, humidity also discourages tools and machines to cool down. And if your tools do not cool down, it might affect their performance drastically. Here are the other factors that your electronics (or things in general) might experience when exposed to too much humidity…

  • Rust
  • Mold
  • Mildew
  • Rot
  • Decay
  • Warping
  • Stretching
  • Lumping
  • Caking
  • Agglomeration
  • Decomposition

And these are some of the devastating consequences you might face when you leave your devices in a room with too much moisture.

The solution to humidity?

Particularly good air conditioning is a vital part of keeping your tools in their optimum health. One way of determining good air in the room in a way that is safe for tools is having a good working air conditioner. Looking back, most HVAC professionals are not even using technology to identify underlying faults in the air. They use a sling psychrometer and a psychrometric chart which can be heavy on the eyes!

However, in the modern times that we live in today, most professionals now opt to use a Fluke 971 Temperature Humidity Meter. Not only does it give real-time results, but it can also give maintenance men little to no downtime. What is more, this tool can measure wet bulb temperature and dew point temperature, psychrometric points that are essential for HVAC evaluations and diagnostics. Here is a short description for each…

  • Wet-bulb – This pertains to the total heat in the air. This represents the cooling effect of evaporating water, the temperature of the air will cool when water evaporates into unsaturated air.
  • Dew point – This is also known as the temperature under which water will condense out of the air.
  • Relative humidity – Ratio of water vapor pressure (amount currently in the air) to the saturation vapor pressure (the amount the air can hold) at a given air temperature.

It is an all-in-one tool for you to determine the optimal performance of the air in the room to make your tools (and people) at a comfortable temperature.

Get your Fluke tools through an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You are in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

SHOP NOW; https://presidium.ph/product/fluke-971-temperature-humidity-meter/

Read more
, , , , , , , , ,

Smart Ways to Save Energy and Prevent Downtime

smart-ways-to-save-energy-and-prevent-downtime

Fluke is a powerhouse tool that can see, hear, and detect all kinds of electricity-related health situations. And that is only one out of a hundred reasons why it is favored by maintenance men and women all over the world. But Fluke tools can only do so much when people get a bit dismissive about caring for their electronics and electricity in general. Therefore energy-saving has become a smart practice for most households, buildings, and facilities. Today, we’ll teach you how to save energy using the most profound test tools in the industry – Fluke test tools.

Moreover, considering downtimes, electricity usage, when abused, can cause downtime. Like all things electronic, they are also prone to wear and faults with excessive use. Therefore adopting healthy practices is always preferable when consuming energy on a daily basis.

Importance of saving energy.

So, when we’re talking about how to save energy, we are not just singling out completely avoiding its use, but rather, we want to introduce smart ways on how you can do it. Energy-saving is a strategy that can completely help the environment, but other than that, it also comes in handy in preventing downtime incidents, abusing your electronics, and inducing excessive use of them.

Take facilities for example. It’s a given fact that most facilities take up loads of energy. And what most people might think is a natural thing that they no longer need to save energy, is a huge misconception. Energy takes up money, and when the electric bills pile up, most managers tend to have a double-take. Remember, we are no longer living in the last decade, this is the 21st century, and prices are hiked up. A quick solution? Have your equipment and machines evaluated and measured. You will never know, one machine might already be causing havoc in a way that is affecting your electric bills, the surrounding environment, and the people working close to it.

To this day, electricity and its availability are almost infinite which is why monitoring, measuring, and testing take a huge significance in establishments. Therefore, we need to consume energy in the most conducive way. In all honesty, electricity and how it is important to our day-to-day tasks can make or break productivity. That’s why, with proper monitoring, we are also at the same time, caring for our businesses or our homes.

Why measurement is relevant to save energy…

In all fairness, measurement is crucial in every point of work to know where you needed to align, adjust, and most of all make strategic decisions to meet goals. This is like our current topic. To save energy, you need to know how much energy is being wasted, you need to gauge if the equipment and machines are the ones that are causing them, and you also need to know which ones need immediate solutions.

Above else, data and logging still reign supreme in businesses, in maintenance, and in a lot of aspects that entail work. You need to measure how much energy you are taking up and see if the numbers are still aligning. This will allow you to document energy waste and machine faults. This information plays a crucial part for future reference.

Ways to save energy…

One of the very known characteristics of Fluke tools is its ability to promote energy-saving, and electronic care, and to give solid solutions to maintenance problems concerning electric machines. The very first thing you want to know when you are saving energy is the health of your electric machines and the overall power that holds them.

And with the help of Fluke tools, this is now achievable in quick and efficient ways. You see, when your electronics are spilling out energy everywhere without you knowing, then your energy-saving methods might be all for naught. This is something you want to check up on daily, especially if you are consuming them every day. So, here are things to keep in mind, on ways to save energy.

1 Mind your bulbs! They can be beneficial to save energy

If you are working in a huge facility, using traditional incandescent lightbulbs can consume excessive amounts of electricity. Try using halogen incandescent bulbs and compact fluorescent lights. Also, take note that fluorescent lights can also have faults. Therefore, it is also preferred for you to use a Fluke Fluorescent Light Tester for easier detection of underlying faults.

2 Turning off lights or appliances to save energy

The simplest and easiest way to save energy is to unplug them when not in use. And we are not just saying to turn the switch off, we mean going the extra mile and unplugging them from sockets. Machines and electronics may seem hardcore materials, but they are also prone to overheating and faults due to excessive use.

3 Be mindful of “Phantom loads”

Not even kidding this is a totally a major source of energy waste. This pertains to electricity used by electronics when they are turned off or in standby mode. Consider the use of smart power strips to eliminate this electricity fault.

4 Check your HVAC systems! They can be a huge factor for you to save energy

This abbreviation stands for Heating, Ventilation, and Air Conditioning. These are three things that also accept much energy in an establishment. There is a number of Fluke tools that can ideally help you with this.

For moisture intrusion:

  • Fluke Ti480 PRO Thermal Camera
  • Fluke 971 Temperature Humidity Meter

For heat loss:

  • Fluke 561 HVAC Infrared and Contact Thermometer
  • Fluke Ti480 PRO Thermal Camera

For monitoring indoor air quality:

  • Fluke 985 Particle Counter
  • Fluke 922 Airflow Meter/Micromanometer

For verifying HVAC system performance:

  • Fluke Ti480 PRO Thermal Camera or Fluke 561 HVAC Infrared and Contact Thermometer

Get your test tools through an authentic source!

Rest assured that through proper measurement, you can achieve the best energy-saving solutions for your establishment, homes, facilities, and businesses. So if you’re currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines, you’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools within Metro Manila.

Read more
, ,

What Is a Three-Phase Power Quality Logger?

what-is-a-three-phase-power-quality-logger

Reliable, quick, and easy, the Fluke three-phase quality logger can perform all the needed studies to ensure the logging of power quality in every machine is accurate and reliable. Like any Fluke tool, the power logger can perform under pressure, is accurate (considering that you do calibration), and can withstand any rough environments. Ideally, this three-phase power quality logger can be used in three different areas of testing.

  • Electrical load studies
  • Energy consumption testing
  • General power quality logging
  • They measure harmonics
  • Electrical power parameters
  • Capturing of voltage events

However, that’s only a gist of what they do. Here, we’ll be able to know more about how a three-phase quality logger can contribute to your electrical machines.

They come with a lot of phases.

They are generally known as power quality loggers, but they also come in the name of “energy loggers”. So don’t get confused when you hear both terms. Anyhow, you’re probably wondering how these things have “a lot of phases”. However, what we truly mean by this is that it comes with variations. Moreover, if you’re spotting a power quality logger, you can find that there is a one-phase logger, two-phase, and of course, a three-phase power logger. So, it’s probably wise for you to assess your machine and your test projects first before getting one.

Its notable applications…

Power quality loggers can be applied to different forms of testing. An authorized Fluke source pointed out its most beneficial functions when it comes to power quality logging. Here are some of them according to an official Fluke source.

  • Load studies – Verify electrical system capacity before adding loads.
  • Energy assessments – Quantify energy consumption before, and after improvements, to justify energy-saving devices.
  • Harmonics measurements – Uncover harmonic issues that can damage or disrupt critical equipment.
  • Voltage event capture – Monitor for dips and swells that cause spurious resets or nuisance circuit breaker tripping.

What does a three-phase quality logger do?

The thing about electrical power usage is that it is continuously and constantly changing. We may find wasted energy one day and wonder where it all came from. And this is the specialty of three-phase quality loggers. Ideally, the main priority of quality loggers is not only to detect the root cause of the problem but is also effective in doing all kinds of tests.

On the other hand, they can also do electrical load studies, energy consumption testing, and general power logging. Furthermore, with the use of Fluke’s three-phase power quality saving, you’ll be able to find out where and when you are consuming energy. A feature that is beneficial for you since you can know where you can adjust certain electrical practices, and this device gives you exactly that. As a result, you can now create credible power-saving strategies to avoid waste.

Finally, when you’re continuously logging energy usage, the three-phase quality logger can effectively assist you in quickly and easily identifying waste faults. Therefore, identifying saving opportunities can be all the easier for you.

The Fluke energy logger commands ease of use and quality performance.

A sweetener for every Fluke device is that it promises easy usability. Even a first-timer can be able to navigate his/her way through a Fluke device and it’s one of its winning qualities. But don’t be mistaken, this tool is more hardcore than you think. Here are more of them.

  • Record power and associated parameters for up to 45 days.
  • Monitor maximum power demand over user-defined averaging periods.
  • Prove the benefit of efficiency improvements with energy consumption tests.
  • Measure harmonic distortion caused by electronic loads.
  • Improve reliability by capturing voltage dips and swells from load switching.

Resolve these failures using Fluke Tools!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools within Metro Manila.

Shop now: https://presidium.ph/shop/?wlfilter=1&product_cat=fluke-power-quality-analyzers

Read more
, ,

Pressure Calibrating Transmitters in Potentially Explosive Atmospheres

pressure-calibrating-transmitters-in-potentially-explosive-atmospheres

It is always a challenging feat to perform operations in a potentially dangerous environment. And even with the greatest test tools that adhere to its user’s safety, you cannot be completely complacent. Pressure calibrating can pose a challenging task when done in a potentially explosive atmosphere. Therefore, when faced with such an assignment, make sure that you have undergone proper training and are equipped with the right equipment.

A deeper understanding of “intrinsically safe”

Primarily, to conduct pressure calibration in a high-risk atmosphere, you need a tool that is deemed “intrinsically safe”. To give a simple explanation, if your tool is intrinsically safe, it means that it is designed to prevent the release of sufficient energy by either thermal or electrical means. Doing so will cause the ignition of flammable material such as gas or dust particles.

In general, intrinsically safe standards don’t just apply to one device or a certain operation, but it applies to all tools and devices that are regularly exposed to potential explosive sources. Here are some of them…

  • Electrical sparks
  • Electrical arcs
  • Flames
  • Hot surfaces
  • Static electricity
  • Electromagnetic radiation
  • Chemical reactions
  • Mechanical impact
  • Mechanical friction
  • Compression ignition
  • Acoustic energy
  • Ionizing radiation

If you are a technician or maintenance man working in industries such as mining, petrochemical, pharmaceutical, or something that exposes you to explosive gases then make sure that your devices are deemed intrinsically safe. Remember, that you are the best asset on the field, so do not take any chances of proceeding with your operation without safe tools to use.

How to pressure calibrate a transmitter in a risky environment.

Now you know all about the device’s safety, let us move on to pressure calibrating a transmitter. It is already a given that you’ll probably tread on eggshells the entire time and try not to provoke the explosive substances that are surrounding you. However, that is not all you need to worry about. The most important thing that you need to do is to perform the procedure carefully and with precision.

Here’s how you can do it according to an official Fluke source:

  1. Depressurize and isolate the transmitter. If opening the transmitter exposes voltages beyond the Intrinsic Safe (I.S.) rating use a continuous monitoring gas detector to monitor for explosive gases.
  2. Plumb the transmitter to the 1/8 inch NPT pressure port of the 718Ex. Connect the test leads per the figure above.
  3. Turn the calibrator on. Vent the calibrator and press zero to zero the pressure displayed. Close the vent control.
  4. Press the UNITS key until PSI shows in the display.
  5. With the 718Ex’s bleed valve open to the atmosphere, press the ZERO key. Close the bleed valve. Set the pressure/vacuum valve to +, for positive pressure.
  6. Use the hand pump to apply 3 psi to the transmitter. Partial pump strokes will apply small increments of pressure. Use the fine-adjust knob to get close to 3.00 psi.
  7. Press the HOLD key and record the psi and mA readings. Press the HOLD key to resume reading.
  8. Calculate and record the error, using: Error = ([(i-4)/16] – [(P-3)/12]) * 100 where Error is in % of span, i is your measured current in mA, and P is your measured pressure in psi.
  9. Repeat steps 5 through 7 at mid-range, around 9 psi, to check linearity at mid-span.
  10. Repeat steps 5 through 7, now at 15 psi, for a check at 100 % of span.
Photo Source: https://us.flukecal.com/literature/articles-and-education/pressure-calibration/application-notes/calibrating-pressure-transm

Purchase from an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You are in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines.

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

Visit our website https://presidium.ph/shop/?wlfilter=1&product_cat=fluke-calibration to know more about our fluke calibration products.

Read more
, , , ,

The Importance Of Electrical Grounding

the-importance-of-electrical-grounding

What is electrical grounding?

Indeed, people have made notable advancements in the electricity department and electrical grounding is one of its big improvements. Technically, electrical grounding is storing electricity on the ground to prevent fatal risks from occurring. It is the process of connecting electrical panels, electrical motors, installations, electrical controls, etc, to the earth. As a result, this will make the environment safer for people since it reduces dangers from civilians and equipment.

What happens if I do not do electrical grounding?

You will be exposed to fatal shocks if your currents are not grounded. So, there are three things about wiring that you need to know about. Ideally, there is an active wire, a neutral wire, and a grounding wire. So, let us look at each one of them closely.

An active wire is the one that supplies power to the wires. Meanwhile, the neutral wire is the one that carries the current back. Lastly, the grounding wire is the one that can be attached to outlets as well as other electrical devices to be connected to the ground at the breaker box.

Originally, the grounding wire is only an additional feature. However, regardless of their “newness” grounding wires holds the most advantageous feature for people since it gives them complete protection from fatal shocks. The grounding wires work for electrical current to safely return to the ground.

As a result, if a short circuit did occur the current would flow through the ground wire causing a blown fuse or tripped circuit breaker. Better a blown fuse or a tripped circuit breaker than a fatal shock, right?

Benefits of proper grounding

Let us face it. Grounding is also one of the most overlooked aspects when it comes to electrical wiring. Nevertheless, according to Platinum Electricians, grounding your wires is an ideal choice to provide protection against possible shocks. They explained. “Grounding your electrical system is a smart and effortless way to make it a whole lot safer, as well as to protect against the very real possibility of having to deal with fluctuations in power supply.”

Just imagine if an electrical error occurs such as lightning strikes or power surges. When you have no electrical grounding, this will cause metal components to function as conductive surfaces. Therefore, these surfaces become electrically energized. And when people touch these surfaces, they will get shocked in the process.

Platinum Electricians further explained by saying, “If you want to safeguard all of your important assets, whether at home or at the office, as well as a lookout for the health and safety of everyone around you, find out if your electrical system is grounded”.”

Advantages of proper grounding according to Conserve Online:

  • Eliminates shock hazard
  • Protects equipment from voltage
  • Prevents electrical fires
  • Reduces equipment repair cost and downtime
  • Lowers levels of electrical noise (fluctuations in an electrical signal)

Why do you need electrical grounding

Not only does it bring notable safety benefits for people and their equipment, but it also brings a lot to the table overall. So, if you do not want your electricity grounded, you might want to think again. Take note of these four significant reasons why you should.

  • Electrical grounding protects against electrical overloads.
  • It stabilizes voltage levels
  • Earth conducts with least resistance
  • It prevents severe damage and death

Resolve these failures using Fluke Tools!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You are in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

List of Fluke models: https://presidium.ph/earth-ground-testers/

Read more