Electric Safety: 5 Preventive Practices to Keep You From Harm During Operations

Method with caution is the rule of thumb of most people who are working with electricity. Live wires or dead wires, one should never be complacent when testing or doing maintenance checks. Nevertheless, there will always be a certain pressure for workers to get the job done no matter what happens. And when certain pressures are breathing down your neck, you might have the tendency to miss a few electric safety steps.

However, missing a few safety steps shouldn’t be something to feel bad about. Actually, even professionals can sometimes make those mistakes. The bigger picture is your safety when you’re around electrical wires. So here are things that you should prevent doing when you’re around them.

Here are preventive practices you should keep in mind when testing electricity…

These are just quick reminders for people who are working closely with live wires (or dead ones) daily. Ignorance of simple things can sometimes be the main cause of a project’s destruction or an immediate trip to the emergency room. Therefore, it’s always a smart move to be very careful and attentive when doing electric testing. Here are some of the common mistakes you should watch out for.

Electric Safety: Working on live circuits

You should limit your exposure to live wires as much as possible. One of Fluke’s best features is its ability to take measurements from afar making its user well protected and away from danger. The best course of action is to de-energize the live wire or switch off the main power source. But then again, why should you vie away from electrical circuits when you have your full protective gear on? It’s because your PPE can only protect you to a certain extent. So, if you’re working with live circuits, better have full insulted tools together with your PPE.

Electric Safety: Refusing to upgrade test tools

You have to upgrade your test tools. We’re not saying you should purchase every time a new one comes out, but if the said tools are going to help you in doing the job better, then, why not right? Good tools are an investment especially if you’re planning on having a career in the electrical department.

Your tool might be working perfectly fine right now but can you still say the same 10 years after? No matter how good your test tool is, opting to purchase a more advanced tool that can keep you safer is always preferred. These advanced tools may be worth the investment than the old ones you have right now.

Electric Safety: Holding test tools with both hands

Actually, try not holding anything at all if it’s possible for you to do so. The goal of every operation is for you to limit your contact to any live wires or any tool that can bring you harm. So, if you must hold your tools when testing electricity, always do it with one hand. Doing so will lessen your exposure to harm if ever there are any unfavorable occurrences.

Nevertheless, the best option for you is to go hands-free (if the operation or the project itself allows it). You can try hanging your device somewhere while testing electricity. Some Fluke tools actually have this feature so that any worker can feel safer doing a ‘hands-free’ job.

Electric Safety: Replacing fuses with cheaper ones.

The fuses that you bought together with your digital multimeter are tested in regards to the CAT safety standards. Moreover, the one that is originally installed in your device can surely withstand any overload or faulty electric wiring. On the other hand, buying from another source might not level up to the original one. It’s always to be better off safe than sorry, so when replacing your digital multimeter’s fuses, buying from an original source is always the ideal choice.

Electric Safety: Don’t neglect your test leads.

One of the most important accessories you can have for your digital multimeters is your test leads. Remember, test leads don’t come in one form. There are a lot of other types that are better suited for the project you are working on. A word of advice, for further safety measures, try looking (or consider purchasing) test leads with finger guards, non-slip surfaces, shrouded input connectors, and those with double insulation.

Purchase from an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines.

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools within Metro Manila.

Read more

Why is Calibration Important?

Often, we hear calibration mentioned when we search for Fluke tools online. But do we really know what it truly means? Calibration is one of the most important steps to knowing if your device is measuring up to its full potential, and that is why it is important. Given that there are different devices, calibration also comes in different forms relating to the tool that needs to be calibrated.

What is Calibration?

A value of a tool is everything. Calibration is the process of comparing a device under test of an unknown value. Only this time there will be a reference standard of a known value. With this process, a thorough reading can be done with the tool being used. By performing calibration to tools, errors can be determined, faults can be found, limitations can be evaluated, etc.

Take thermometers as an example. It is a given fact that thermometers measure temperatures, right? You can conduct a calibration test on thermometers by putting them in water with a boiling point of 212 degrees Fahrenheit. By doing so, you will be able to learn the errors that the thermometer holds. Remember, visual facts hold less than actual testing. And by placing calibrated reference thermometer under a series of tests, you will be able to find out its precise value. One of them is putting the device under test, which is the thermometer into the water, yes that is one way to do it.

But do not be mistaken, calibration is not an act of corrective adjustment. Corrective adjustment is completely different from calibration which also requires the use of different methods. Nevertheless, calibration is a process that leads you to the step of corrective adjustment only if it applies to the device.

Why is it important?

Calibration tools are relied upon by many professional engineers, technicians, metrologists, and more. This is because calibration can help them gain more confidence regarding the tool’s safety and reliability. It is not just tools that are calibrated but a lot of things such as flights, medications, nuclear facilities, computers, appliances, cell services, and many more. These industries also go through the process of calibration to not only ensure safety and reliability but also for quality and cost.

Calibration is a way to make sure that all tools are working in their optimum condition. Moreover, it is also a way to prevent failures when in use or while in production.

But that is not all, what makes this all the more impressive is its enablement to open doors to opportunities. Calibration takes steps (considering that it is continuously developing) to improve scientific discovery and industrial manufacturing.

The Chief Corporate Metrologist of Fluke Corporation

Jeff Musk actually has some very important insights regarding the importance of Fluke calibration. According to the chief, he said, “If you are performing measurement where the results will make a critical decision such as a safety test or if a manufactured product meets requirements, you must have your equipment calibrated so that the performance is known and fit for purpose. This is especially important if you want your results to correlate with others around the world.”

Another fact of why calibration is important is because all things wear down, especially with electronics. Overall, expect that your device will not look, feel, and perform as it once was when it was brand new. Expect that there will be lapses in time. But by doing the annual calibration, you will be able to make sure that it operates properly based on its product specifications.

Different kinds of calibration.

There are various kinds of Fluke tools in the market, each boasting special functions, and applications in different electrical or mechanical work. With this said, it is ideal to have not one but multiple calibration tools to make sure each device works properly and perfectly in different projects or operations. Fluke has six different calibration tools that you need to know about. Here are some of them…

  1. Electrical
  2. RF
  3. Temperature
  4. Humidity
  5. Pressure
  6. Flow

Calibrate through an authentic source!

Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Rest assured that all tools have gone through proper tests to prevent faults from penetrating your projects that might cause bad downtimes by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

You could reach us at info@presidium.ph / calservices@presidium.ph for inquiries.

Read more

All You Need To Know About Non-Contact Voltage Testers

Being one of the sought-after tools in the market, Fluke’s non-contact devices take center stage. Fluke being able to create tools that can help workers take tests and measurements from a safe distance is one of its defining features. Expect that almost half of the test tools will have this winning function.

On the other hand, non-contact voltage testers don’t stray far from its family of digital multimeters. Only this time, they offer a more direct approach to detecting voltages. Not to mention, they are also very handy in terms of sizes. Here, we will be discussing all you need to know about them!

What is a Non-Contact Voltage Tester?

For staff in the electrical, industrial, and maintenance departments, this is a huge sigh of relief. Gone are the days of hesitant testing and risking people’s safety. To put it plainly, non-contact voltage testers are used to see if the voltage is present or not. Additionally, this tool can also detect mis wires of electrical outlets.

This portable tool is very well-liked for its simple and quick approach to see if the harmful voltage is taking place within your outlets or electrical panels. What is better? It does not entail a lot of buttons pushing or navigating, but it is mostly favored by maintenance people for its direct approach.

Choosing the right Non-Contact Voltage Tester for you.

There are diverse types of non-voltage testers. It’s best if you assess the operations, you usually do before purchasing a non-contact voltage tester to make the most out of it. Plus, keep value in mind when looking at non-contact voltage tester prices and remember that the best price does not necessarily equal the best value. With this said, take note of these Fluke non-contact voltage testers to determine the one for you.

Fluke 1AC II VoltAlert™ Non-Contact Voltage Detector

The Fluke 1AC II Volt Alert is perfect if you need a high-performing tool for general voltage detection. Uneasy leaving tools to shut down on its own? This non-voltage detector comes with an on/off switch of your convenience.

Here are more of its notable capabilities:

  • Voltage range: 90 V to 1000 V AC
  • Voltbeat™ technology and continuous self-test — so you always know it is working
  • Voltage indication: tip glows and beeper sounds (beeper can be disabled)
  • Safety: CAT IV 1000 V
  • On-off switch for maximum battery life

Fluke 2AC VoltAlert™ Non-Contact Voltage Detector

The Fluke 2AC Volt Alert is perfect for people who usually work in environments wherein sight indication is more preferred than sound. If you are a person who’s always on the go and needs a ready stead voltage detector, then the Fluke 2AC VoltAlert is the one for you. Although it still does feature audio beep voltage indicators, so technically speaking it’s just a tad bit more advanced than Fluke 1AC considering its extra features.

Here are more of its notable capabilities:

  • 90 V to 1000 V AC voltage range
  • Voltage indication: tip glows
  • Voltage indication: audio beeper for quiet environments
  • Safety: CAT IV 1000 V
  • Always on, using special low power circuitry to sustain battery life and ensure your 2AC is always ready
  • ‘Battery Check’ function ensures battery is in good condition

How do non-contact voltage testers work?

As we’ve mentioned, it is very simple and direct. Just touch the tip of your non-contact voltage tester to an electrical strip and wait for a beeping sound. Also, watch if the point turns either red or green. Red light indicates that high voltage is present while a green light tells that the wire does not harbor any dangerous voltages.

Here are things you should also remember when operating a non-contact voltage tester…

  • The tip glows red and a beeper sounds when voltage is detected
  • A loud, easy to hear beeper will sound and the tip will glow red when voltage is detected
  • Optionally, the beeper can be disabled for use in quiet environments
  • Continuous self-test so you always know it is working
  • When the tip blinks red you know it is working properly
  • Provides a continual visual indication that the 1AC II is on
  • 90 V to 1000 V AC or 200 V to 1000 V AC voltage detection range for wide application use.
  • Wide voltage detection range allows for use in a broad range of applications
  • Also available in a low voltage model from 20 V to 90 V AC for controls circuits

Can I get shocked while using a voltage tester?

We know, it is the complete irony for a device to be called “non-contact” and still require contact when being used. However, if your concern is getting shocked then let us put you at ease. Fluke specializes in making tools that prevent workers from getting hurt, and this does not leave out the Fluke voltage testers. 

Considering shocks, make sure that you are using and holding your voltage tester properly. Doing so will shield you from shocks. Only hold them on the insulated handle when you are undergoing an operation.

Okay, so we’ve touched up where to hold your voltage tester. Now, let us talk about watching where you are placing your other free hand. Make sure that it is not touching something that will expose you to live currents still (if ever the insulation fails).

Another word of advice, never undergo testing without wearing the proper personal protective equipment. Tools are just covering one part in protecting you from electrocution but having your PPE will provide you the complete safety and confidence you need when you’re working with these kinds of projects.

Some non-contact voltage testers can show a false positive or negative if…

Environmental factors can play a key role in getting accurate data from test tools. These are things that you need to consider, and from time to time, adjust to. Like all tools alike, the non-contact voltage tester is not different. At times, the device may show false positive or negative results. This is why it is especially important for you and your safety to take note of what is causing them for prevention purposes.

Reasons for false positive or negative:

  • The insulated test point touches grounded metal
  • The cable being evaluated is partially buried
  • The user is isolated from ground
  • The tester is used inside a metal enclosure
  • The cable is shielded
  • The battery is dead

The difference from other non-contact Fluke devices.

Fluke’s main priority is developing test tools that will keep workers and maintenance people safe in every operation. And to this day, they have kept their promise of providing workers the best test tools there are. This superbly handy non-contact voltage tester, however, differs from most since, well, it is smaller with more direct functions. No need to press a lot of buttons, no complicated navigation, and you will not even spend time reading the manual for this one. That is one of the winning factors of this test tool.

Purchase from an authentic source!

Hey, you made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your machines? You are in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines.

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

Fluke 1AC: https://presidium.ph/product/fluke-1ac-a1-ii-non-contact-voltage-tester/

Fluke 2AC: https://presidium.ph/product/fluke-2ac-non-contact-voltage-tester/

Read more

Top 13 Causes of Rotating Motor Failure from Lowest to Highest

The number one priority of maintenance men is to focus on machine faults, errors, or defects and stop them before they even happen. After diagnosing the machine, they will then settle on the most suitable tool to get the job done.

However, considering rotating machines, things can always get a tad bit tricky. These kinds of machines are prone to imbalance, looseness, misalignment, and wear. Naturally, the best way to deal with them is by having regular checkups with the most trusted test tool in the industrial department, and those are Fluke test tools.

But first, here is the top thirteen causes of motor failure…

Motors are saturated everywhere especially in industrial departments. However, over time, these motors are also prone to malfunction and eventually slow down. Naturally, they become more complex and technical which may prove to be a challenge for maintenance men to fix without the right tools. Let us delve into the top thirteen causes of motor failure for better understanding.

Rotating Motor Failure: Power Quality

  • Transient voltage

The impact? Motor winding insulation. Technically, it is going to break down leads that will lead to motor failure and will eventually lead to long downtimes.

Criticality status – High

  • Voltage imbalance

The impact? This will create an excessive current flow. It will impact one or more phases that will increase operating temperatures. In the end, it will lead to insulation breakdown.

Criticality status – Medium

  • Harmonic distortion

The impact? Briefly, what happens is a decrease in motor efficiency. You see, harmonic distortion is additional energy that is used in the motor shaft. However, this kind of energy also contributes to internal energy losses that are bad for the machine. It can come in the form of heat and over time will cause deterioration of the insulation of the windings.

Criticality status – Medium

Rotating Motor Failure: Variable Frequency Drives

  • Reflections on drive output PWM signals

The impact? Motor winding insulation breakdown. This is also the works of impedance mismatches that root out from improper installation, improper component selection, or equipment degradation over time.

Criticality status – High

  • Sigma current

The impact? Mysterious circuit trip caused by protective earth current flow.

Criticality status – Low

  • Operational overloads

The impact?  This might do permanent failure to your machine since it causes premature wear on motor electrical and mechanical components.

Criticality status – High

Rotating Motor Failure: Mechanical Faults

  • Misalignment

The impact? There are three types of misalignments that could occur. This is angular misalignment, parallel misalignment, and compound misalignment. All of which leads to premature wear in mechanical drive components.

Criticality status – High

  • Shaft imbalance

The impact? This may be caused by a lot of factors such as dust accumulation, missing balance weights, manufacturing variations, and a lot more. This will result in premature wear in mechanical drive components and total mechanical failure.

Criticality status – High

  • Shaft looseness

The impact? You see, a looseness that is caused by the actual rotation might stem out from excessive clearance between rotating and stationary elements. This can also result in premature wear and failure.

Criticality status – High

  • Bearing wear

The impact? Remember that this can also cause by several things. These are:

  • A heavier load than designed for
  • Inadequate or incorrect lubrication
  • Ineffective bearing sealing
  • Shaft misalignment
  • Incorrect fit
  • Normal wear
  • Induced shaft voltages

Ultimately, accelerated wear on rotating components can result in bearing failure.

Criticality status – High

Rotating Motor Failure: Improper Installation Factors

  • Soft foot

The impact? There are two types of “soft foot” that you need to know about. There is a parallel soft foot and angular soft foot. Parallel soft foot takes place when one of the mounting feet is higher than the other three. Meanwhile, angular soft foot happens when one of the mounting feet is not parallel or “normal” to the mounting surface. But in totality, it heavily makes an impact on the misalignment of mechanical drive components.

Criticality status – Medium

  • Pipe strain

The impact? This will generally put a strain on rotating components and will cause shaft misalignments. Naturally, this will also result in premature failures.

Criticality status – Low

  • Shaft voltage

The impact? Arcing across bearing surfaces create pitting and fluting resulting in excessive vibration and eventual bearing failure

Criticality status – High

Resolve these failures using Fluke Tools!

Hey, we made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your rotating machines? Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your rotating machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

Read more

FieldSense Technology: Creating A Safer Way for Simultaneous Voltage and Current Measurements

Working on electrical wiring and high voltages can be a hazardous undertaking. Although there are preventive measures that one can implement (such as PPE’s and insulated tools) this can only do the bare minimum when you’re under electrical dangers. Luckily, with the innovations of technology, maintenance workers can be more at ease when doing high-risk rounds. By using the new and improved FieldSense technology it can guarantee more safety for the men at work. Its improved functions can attest to this.

However, maintenance professionals are aware of the risks and have undergone preventive training. It’s always preferable to work with tools that can ensure safety and can do the job right. And Fluke tools have just about every unit of these safe and efficient devices that is every maintenance man’s dream tool.

What is FieldSense Technology?

In simple terms, FiledSense Technology is the new and improved way of measuring simultaneous voltage and currents. Basically, the traditional way of measuring such risky parts of a machine or panels is by poking and touching certain parts of the machine that can endanger a man at work. 

However, with the use of FieldSense Technology, it has the capacity to eliminate more risks. Initially, the old way of measuring this is by being in contact with electrical conductors with the use of test leads. This method requires metal-to-metal contact that may carry potential arc flash or electrical shock.

But then again, with the use of this advanced tool, it’s one worry of maintenance and troubleshooting men that they can finally be at peace with.

Safe measurements using FieldSense Technology.

We’re running down facts on how using FieldSense Technology can benefit you on the field. Ultimately, workers (such as commercial and industrial electricians) can use Fieldsense technology for voltage and current measurements, verifying continuity values, and testing individual circuits. However, there is more to this device than just those previously stated.

Aside from its amazing functions, these are some of the things on how this devi9ce can benefit any maintenance or troubleshooting professional on the field.

An option of no metal-to-metal contact

One of the greatest and most favored functions of FieldSense Technology is its ability to measure without metal contact. Unlike most devices that need test probes or alligator clips that need to be connected to the conductor to get accurate readings, FieldSense technology does not require those technicalities.

Basically, in doing so, you are also putting your safety at risk since these kinds of procedures may trigger sparks, arc flashes, or electric shock.

However, by using the new and advanced Fluke FieldSense Technology, you can put yourself at ease since it doesn’t require any contact. This technology allows you to measure ac voltage, current, and frequency through the cable’s insulation by sliding the fork of the tester over the conductor. Therefore, there will be no direct electrical contact with live voltage lessening the risks of dire circumstances.

FieldSense Technology offers more than fault detection.

There will be no shortage of devices that can measure voltage and Fluke tools are one of them. Being recognized as one of the best test tools in the market, Fluke innovates devices to further meet the needs of workers in this continuously advancing world. With this said, Fluke FieldSense offers this kind of innovation by going beyond voltage detection.

Ultimately, this device can also offer to accurately measure the given voltage. Basically, by having this device in your back pocket, you now have voltage detection and a measurement tool, all in one device! Sounds great? There’s more coming! 

FieldSense technology can reduce the need to open panels.

Fluke FieldSense is also known for its fast and easy measurement methods. One of the ways that this device is tagged as a quick measurement tool is because it doesn’t really require you to open any panels. Have the ease to take measurements at any point along the conductor. Technically, you only need to slide its fork-like top to one of the single conducting wires and read the results. Easy and one, two, three!

Take measurements without fussing.

No need to worry about test leads or probes with this one. And when we say you no longer need them, we mean it! FiledSense can still accurately measure voltage without them. What’s cool? Because you no longer need additional accessories for this one, you can have the ability to multitask. Have your FieldSense technology on one hand while doing other priorities on the other.

Its fork-like top can give you the ease of isolating individual hot and neutral wires which in turn helps reduce the chance of accidental contact with another voltage point and the likelihood of errors. Save more time and accomplish more things with this little device!

It promotes proper operation.

Initially, when you’re about to operate on something using any Fluke device a rule of thumb before each operation is making sure that the FLuke device is working smoothly before undergoing any tests. In as much, the FieldSense technology makes sure of this. If you’re a newbie on the field have the habit of testing your device before and after living tests to ensure security and more accurate measurements.   

Get your Fluke tool from a trusted source!

Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools in the market!

Read more

Fluke Maintenance Tools: The Future of Renewable Energy

We are living in an ever-changing world where innovation is not slowing down. People always look to the future for new and exciting things to try. In this regard, it’s technology that holds the number one spot in terms of advancement. 

However, it’s no secret that it’s also the top cause of pollution and the degradation of the earth. Mobile phones alone actually contain harmful toxins when discarded. Ultimately, these devices (and others) have the ability to contaminate groundwater and soil; two of the most vital elements keeping nature alive. In the long run, if these toxic technological innovations are not remedied, it’s continuously going to destroy our lands.

Because of the sudden surge of technological waste, professionals are now trying to promote clean and sustainable energy. One of them is Wind Power and Solar Energy. These technological advancements are believed to be the future of electricity. And what better way to maintain these devices than the most trusted Fluke Maintenance Tools in the market.

What is renewable energy?

The future of energy is looking golden. As we try not to wreak havoc in the natural movements of things, experts have found a way to sustain the richness of nature by using it as the main conduit of electricity and power. That is renewable energy. 

Advantages of using renewable energy.

One of the most prominent advancements in the industry is wind energy and solar energy. Not only is it benefiting the industry and the world’s natural resources, but it is also benefiting the people in more ways than one. Here are some of its notable advantages:

Wind power and solar energy are cost-effective.

Wind doesn’t just benefit us by blowing cool air on our faces on a hot day, but it can also give us the most needed necessities in our day-to-day lives, which is electric energy. This kind of renewable energy is actually recognized as one of the low-priced energy sources that are currently available. Ultimately these giants use the wind to convert energy produced by the movement of wind turbine blades to power establishments and other spaces. The bottom line is, the wind is free. As long as you got wind, then you can get energy. 

Meanwhile, solar energy is also one of the most in-demand tools of the current date that many households have decided to install. This is because it is also one of the most cost-efficient devices for you to power up your systems. Not only is it low-cost but it is also tagged as one of the low maintenance sources of power you can get your hands on. The only thing you have to do to maintain it is to keep it clean.  

It’s a clean fuel source.

When we say that these tools are the ultimate eco-friendly resources to produce energy, we weren’t kidding. Compared to power plants, wind power and solar energy does not omit the combustion of fossil fuels, coal, natural gas, nitrogen oxides, and other harmful elements. Moreover, these technologies also do not cause atmospheric emissions that cause acid rain, smog, or greenhouse gases. Instead, it solely relies on wind and the sun to create energy.

Wind and solar power create jobs.

With technology as big and vast as this, you would need to have a lot of people maintaining it and technically, keeping it alive and going. Therefore, it has also become one of the fast-growing careers in terms of manufacturing, installation, maintenance, and supporting services by 2050 according to the Department of Energy.

Common disadvantages:

  • Spinning turbines can kill flying birds
  • Bats have also been killed by turbine blades
  • It can be a bit noisy
  • Can be a photobomber in most aesthetic landscapes (unless you think otherwise)
  • The installation process might be costly
  • Weather dependent
  • Uses a lot of space

Fluke tools are the future of renewable energy.

The best maintenance tools in the market come in the many forms of Fluke Tools. In a nutshell, Fluke tools are the most advanced test tools in the industry that can capture, diagnose, and make solutions to the most challenging technical difficulties maintenance men can encounter. 

Wind and solar power do make matters easier in terms of sustainable energy. Yes, they basically only need natural resources, such as sunlight and wind to function, but that doesn’t mean that they no longer need maintenance themselves. These technologies actually need regular maintenance checks and the best tools to perform these rounds are with Fluke Tools. 

With a wide selection of the best troubleshooting and maintenance devices, this is your one-stop-shop for all your device needs when it comes to caring for wind and solar energy tools. When we’re talking about the future of sustainable energy, ultimately, we also need to think about the tools we need to sustain and care for them and this entails the best performing tools in the industry which is Fluke tools. 

Get them from a trusted distributor in the Philippines: https://presidium.ph/

Read more

Best Fluke Clamp Meters For Industrial Use

Clamp meters are widely saturated because of their convenient and safe measurement functions. Believe it or not, without these innovative test tools, people would still be cutting wires and inserting test leads into the circuit to take an in-line current measurement. But this is old news. Thanks to advanced technology, people no longer need to perform drastic operations, when they want to make safe measurement rounds. These clamp meters for industrial use, prove to be a significant tool to every maintenance man or technician.

To this day, a lot of industries are in need of good functioning machines, wires, panels, and a lot more. Evidently, they need a tool that can perform well under pressure even in the roughest environments. This is where the expertise of clamp meters comes in. Basically, clamp meters are digital multimeters with current sensors. Ultimately, this combination makes them one of the most remarkable tools when you need to measure high current applications.

With Fluke Clamp Meters for industrial use, measurements are done quickly and safely without interrupting the flow of current and without the need for test leads. Now, let’s get to know the best fluke tools for industrial use!

Mostly, this is what your clamp meter consists of…

You could probably spot a clamp meter amongst other fluke devices simply because of its iconic red clamp situated at the top of the device. Yes, every clamp meter is different, but these features will most likely be present in each of them.

  • Transformer Clamps – It senses the magnetic field of the current flowing through the conductor.
  • Clamp Opening Trigger – It is used to open the clamp on top.
  • Power Switch – It simply turns the device on and off.
  • Back Light Button – Its function is to light up the LCD display for easier reading when you’re doing operations in the dark or at night.
  • Hold Button – Used to hold the last value on the display.
  • Negative / Ground Input Terminal – For connectivity purposes, it is used to join the negative/ ground jack of the meter cable.
  • Positive Input Terminal – Used to connect the positive jack of the meter cable.
  • LCD Display – It displays the measured value.
  • Functional Rotary Switch – It is used to select the type and range of current being measured.

Clamp Meters for Industrial Use

The Fluke 355 True RMS AC/DC Clamp Meter for industrial use is the perfect tool when you’re measuring up to 2000 amps. The Fluke 355 also showcases wide jaws that can easily clamp around large conductors typically found in high current applications. One of the most applauded features that this clamp meter has is its ability to measure AC/DC currents. Additionally, you can also take accurate peak measurements that can be taken using the in-rush current mode. This feature is ideal when measuring motors and inductive loads. The 355 also measures voltage and resistance, making this the most versatile tool for utilities, electrical contractors, and industrial service technicians.

Other notable features:

  • Quickly analyze readings using the MIN, MAX, and AVG functions.
  • Use the low-pass filter to smooth out noisy loads and stabilize readings.
  • CAT IV 600 V, CAT III 1000 V rating for added user protection.
  • A large backlit display allows for easy visibility in low-lit areas.
  • Use the display hold feature to capture readings even when the display cannot be viewed.

Fluke 376 True RMS AC/DC Clamp Meter with iFlex®

Expand Your Measurement Range with Increased Flexibility. You can measure around awkward-sized conductors with the Fluke 376 True RMS Clamp Meter with iFlex®, expanding your measurement range to 2500 A AC. With True RMS voltage and current measurements, the Fluke 376 can read up to 1000 V and 1000 A in both AC and DC modes.

Key features:

  • iFlex® Flexible Current Probe expands the measurement range to 2500 A AC
  • CAT IV 600 V, CAT III 1000 V
  • True RMS AC voltage and current for accurate measurements on non-linear signals
  • Min, max, average and Inrush recording to capture variations automatically
  • Integrated low pass filter and state-of-the-art signal processing allows for use in noisy electrical environments while providing stable readings

Get one from a trusted distributor.

Presidium PH is one of the trusted distributors of Fluke tools in the Philippines. They have a wide selection of test tools and Fluke accessories to choose from on their website. Therefore, if you want to have the best Fluke troubleshooting tools for industrial use in your possession, get it from Presidium PH!

Read more