Top 13 Causes of Rotating Motor Failure from Lowest to Highest

The number one priority of maintenance men is to focus on machine faults, errors, or defects and stop them before they even happen. After diagnosing the machine, they will then settle on the most suitable tool to get the job done.

However, considering rotating machines, things can always get a tad bit tricky. These kinds of machines are prone to imbalance, looseness, misalignment, and wear. Naturally, the best way to deal with them is by having regular checkups with the most trusted test tool in the industrial department, and those are Fluke test tools.

But first, here is the top thirteen causes of motor failure…

Motors are saturated everywhere especially in industrial departments. However, over time, these motors are also prone to malfunction and eventually slow down. Naturally, they become more complex and technical which may prove to be a challenge for maintenance men to fix without the right tools. Let us delve into the top thirteen causes of motor failure for better understanding.

Rotating Motor Failure: Power Quality

  • Transient voltage

The impact? Motor winding insulation. Technically, it is going to break down leads that will lead to motor failure and will eventually lead to long downtimes.

Criticality status – High

  • Voltage imbalance

The impact? This will create an excessive current flow. It will impact one or more phases that will increase operating temperatures. In the end, it will lead to insulation breakdown.

Criticality status – Medium

  • Harmonic distortion

The impact? Briefly, what happens is a decrease in motor efficiency. You see, harmonic distortion is additional energy that is used in the motor shaft. However, this kind of energy also contributes to internal energy losses that are bad for the machine. It can come in the form of heat and over time will cause deterioration of the insulation of the windings.

Criticality status – Medium

Rotating Motor Failure: Variable Frequency Drives

  • Reflections on drive output PWM signals

The impact? Motor winding insulation breakdown. This is also the works of impedance mismatches that root out from improper installation, improper component selection, or equipment degradation over time.

Criticality status – High

  • Sigma current

The impact? Mysterious circuit trip caused by protective earth current flow.

Criticality status – Low

  • Operational overloads

The impact?  This might do permanent failure to your machine since it causes premature wear on motor electrical and mechanical components.

Criticality status – High

Rotating Motor Failure: Mechanical Faults

  • Misalignment

The impact? There are three types of misalignments that could occur. This is angular misalignment, parallel misalignment, and compound misalignment. All of which leads to premature wear in mechanical drive components.

Criticality status – High

  • Shaft imbalance

The impact? This may be caused by a lot of factors such as dust accumulation, missing balance weights, manufacturing variations, and a lot more. This will result in premature wear in mechanical drive components and total mechanical failure.

Criticality status – High

  • Shaft looseness

The impact? You see, a looseness that is caused by the actual rotation might stem out from excessive clearance between rotating and stationary elements. This can also result in premature wear and failure.

Criticality status – High

  • Bearing wear

The impact? Remember that this can also cause by several things. These are:

  • A heavier load than designed for
  • Inadequate or incorrect lubrication
  • Ineffective bearing sealing
  • Shaft misalignment
  • Incorrect fit
  • Normal wear
  • Induced shaft voltages

Ultimately, accelerated wear on rotating components can result in bearing failure.

Criticality status – High

Rotating Motor Failure: Improper Installation Factors

  • Soft foot

The impact? There are two types of “soft foot” that you need to know about. There is a parallel soft foot and angular soft foot. Parallel soft foot takes place when one of the mounting feet is higher than the other three. Meanwhile, angular soft foot happens when one of the mounting feet is not parallel or “normal” to the mounting surface. But in totality, it heavily makes an impact on the misalignment of mechanical drive components.

Criticality status – Medium

  • Pipe strain

The impact? This will generally put a strain on rotating components and will cause shaft misalignments. Naturally, this will also result in premature failures.

Criticality status – Low

  • Shaft voltage

The impact? Arcing across bearing surfaces create pitting and fluting resulting in excessive vibration and eventual bearing failure

Criticality status – High

Resolve these failures using Fluke Tools!

Hey, we made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your rotating machines? Presidium PH is an authorized distributor of Fluke test tools in the Philippines. Prevent these faults from penetrating your rotating machine by using the best test tools there are!

If you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools within Metro Manila.

Read more

Importance of Maintaining Battery Backup Systems

Come to think of it, can you imagine an airport without electricity, a shopping mall without lights, or hospitals without functioning technology? Just the thought of it is disastrous in it itself. Moreover, this just shows how reliant we are on electric power and how we depend on them on a day-to-day basis. Big and important establishments depend on electricity every day, and when that electricity goes out, it comes to the battery backup systems.

What are battery backup systems?

Along with battery backup systems come uninterrupted power supplies and a string of batteries. Technically, they are what we turn on when everything is down. But, nevertheless, this doesn’t mean that they are not susceptible to corrosion, deterioration, internal short circuits, sulphation, dry-out, and seal failures.

Safe to say, they are our second line of defense when an outage occurs. Naturally, when you keep your battery backup systems in shape, you’ll be prepared to turn the power back on immediately until stable power comes through.

Industries banking on backup systems.

So, earlier, we’ve mentioned big industries that benefit from having backup systems, they’re actually not the only ones. In short, there are a hundred industries that bank on this power to fuel their day-to-day operations when actual power distributors experience faulty systems.

Here are some of them:

  • Hospitals
  • Medical centers
  • Electronics manufacturers
  • Data and call centers
  • Banks
  • TV stations
  • Production-based manufacturers
  • Telecommunications and cable companies
  • Universities
  • Utility companies
  • Restaurants
  • Shopping centers
  • Airlines

Common reasons for power loss.

There are certain circumstances that are completely out of our hands that cause power loss and in return, urge the use of battery backup systems. Although few of these situations are rare, they can still take place at any moment. Moreover, according to Constellation, these are the top 10 reasons for power loss:

  • Severe weather
  • Natural disasters
  • Motor vehicle accidents near power lines
  • Equipment failure
  • Fallen trees
  • Wildlife interference
  • Hight energy demand
  • Power line damage from construction work
  • Damage from the public
  • Cyberattacks
  • Planned power outages

Main types of battery backup systems.

According to Warren CAT, there are three types of battery backup systems. These are the standard UPS, line-interactive UPS, and double conversion UPS. Usually, bigger battery backup systems include switchgear and a power transformer to provide consistent and reliable electricity. Having this kind of technology can guarantee fewer downtimes in a year, it’s actually possible to have a few to none at all.

Let’s take a closer look at the three types of battery backup systems:

  • Standby UPS system – It normally has an inverter, battery, static switch, low-pass filter, and surge suppressor. Basically, the system remains on standby unless there’s a primary power failure.
  • Line-interactive UPS system – Contains a battery and inverter that are always connected to the output, and if power fails, a switch changes the electrical flow. Furthermore, the continuous connection provides superior filtering.
  • Double-conversion UPS system – Additionally, this device has a backup battery that is charged by the input AC and powers the output inverter for a seamless switch.

The Fluke tool that’s perfect for battery backup maintenance.

The most ideal tool for maintaining battery backup is Fluke Battery Testers. Moreover, as stated in their official site, here are some of Fluke Battery Tester’s best key features:

Battery Voltage

Initially, during the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test.

Discharge Volts

The Discharge mode collects the voltage of each battery multiple times at a user-defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery.

Ripple Voltage Test

Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. ultimately, it allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration.

Meter and Sequence Modes

Likewise, you can save and read the readings in a measurement or time sequence. On the other hand, the sequence mode is for maintenance tasks with multiple power systems and battery strings.

Threshold and Warning

Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement.

Intercell Strap Resistance Test and Data Management

Measures the resistance of the intercell connection between batteries in a string.

AutoHold

When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts.

AutoSave

When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured.

Fluke Battery Management Software

Meanwhile, easily import data from the Product to a PC. The measurement data and battery profile information is stored and archived with the Management Software and can be used for comparison and trend analysis. All measurement data, battery profile, and analysis information can be used to easily generate reports.

Comprehensive logging

All measured values are automatically captured during testing and can be reviewed on the instrument before downloading for on-the-go analysis.

Optimized user interface – Quick, guided setup ensures you’re capturing the right data every time.

Battery life – 7.4 V 3000 mAh lithium-ion battery for more than eight hours continuous operation.

USB port – Meanwhile, for fast data download to supplied data analysis and report management application software.

Highest safety rating in the industry – CAT III 600 V, 1000 V dc max. rated for safe measurements all around the battery power supply equipment.

Get your Fluke tool from a trusted source!

Hey, we made it to the bottom! Are you currently looking for the best-performing test tools in the market to run daily maintenance checks on your UPS? You’re in luck cause Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fluke tools and their functions, visit our website for more info!

Read more

Fluke Thermal Cameras: How Wind Affects Thermal Reading

Thermal energy can be found all around us. Even our own bodies emanate hot and cold energy and that also goes for our surroundings. If you think of it, thermal cameras (or imagers) are actually one of the most sophisticated devices we have in terms of troubleshooting. Honestly, this device shows actual heat on the screen! That alone says a lot about technology advancement. Wait till you learn more about Fluke Thermal Cameras, but we’ll get to this a bit later.

Nevertheless, things are not always a hundred percent with thermal cameras (or any other device in general). This is because surrounding elements can always affect readings. And when the man in charge is not aware of the possible elements that can affect outputs, and this will cause inaccurate data.

How does wind affect readings?

It all goes down to understanding the basic principle of heat transfer. You see, thermal energy varies from hot to cold (or vice versa) which is the basic principle of temperature. This is so unless another force comes in between that process and alters it completely. And when we say “another force” this means the wind. Yes, the wind is a viable candidate for temperatures to be manipulated. As a result, this can alter a surface’s temperature.

On the other hand, when you use a thermal camera to inspect an object (whether it’s on the inside or outside) you also need to take your environment into consideration. In line with this, there is a thing such as forced convection. Forced convection is a form of heat transfer that comes from wind, fans, pumps, suction devices, etc. Basically, these are elements that have the ability to change your target temperature. 

A deeper understanding of forced convection.

Think of it this way, if you make hot tea it is already a given that it’s not going to stay hot for quite some time. This is because heat tends to get lost in the surroundings. Technically, forced convection is the interruption of external aspects turning originally hot objects into cooler ones or vice versa.

There are actually two types of convection you must know about. One of them is forced and the other is natural. To briefly explain the two elements, forced convection (as we’ve mentioned above) is caused by objects. But on the matter of natural convection, this is actually influenced by the natural flow of things. Some examples of this are the sea breeze and land breeze.

Wind can cause a change in reading.

Don’t be alarmed, we’re not talking about drastic changes but yes, there is change when the wind is applied to readings. So it’s safe to say that if you want accurate readings on your data, best have a wind meter handy. However, if you don’t have a wind meter on hand, there is actually another way of determining which kind of wind you are dealing with.

But first, you must know and understand the Beaufort Scale. To put it lightly, the Beaufort Scale is a scale of the wind speed based on visual estimation of the wind’s effects from zero to twelve. Here’s a chart according to the Royal Meteorological Society.

Beaufort Scale

ForceSpeed (mph)Description
0<1Calm
11-3Light air
24-7Light breeze
38-12Gentle breeze
413-18Moderate breeze
519-24Fresh breeze
625-31Strong breeze
732-38Near gale
839-46Gale
947-54Strong gale
1055-63Storm
1164-72Violent storm
1273+Hurricane

Environmental adjustments you can tweak.

Realistically speaking, you cannot make tweaks or adjust every inspection environment you enter! Such a thing is not always doable. Nevertheless, what you can make up for it though is to be prepared. Here is something thing you can do!

During an indoor inspection, air conditioning and other HVAC appliances may have an effect on readings. The best way to prevent forced convection is by turning off the HVAC system before performing any operation.

With outdoor windy environments, however, unless you can control the weather and stop the wind, it might be trickier than usual. But the best way to go about this is to examine older data, inspect the machine thoroughly, and adjust settings accordingly.

About Fluke Thermal Cameras…

Fluke Thermal Cameras actually has advanced features than most. But be aware that there are also different kinds of them with slightly different functions. However, like any other thermal camera, each unit will let you take quality thermal readings with the following functions:

  • Continuous touchscreen IR-Fusion
  • 5 hours battery life.
  • Can withstand drop up to 2 meters.
  • Water and dust resistance. IP54 enclosure rating.
  • Automatically organize and file thermal images with Fluke Connect.
  • 120 x 90 infrared resolution.

But in totality, whatever thermal camera you choose can benefit you and your work greatly, no doubt!

Here are some of its advantages for you:

  • Can collect data in hazardous environments from a safe distance.
  • Scanning large areas such as walls, ceilings, and roofs quickly.
  • Gathering data without disrupting production.
  • Quickly identifying irregularities in specific locations.
  • Detecting problems before failure.

Get your Fluke tool from a trusted source!

Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools in the market!

Read more

4 Main Causes of Machine Faults

Machines are unpredictable things. It can be working properly and then the next, they can be coughing up oil, making unusual buzzing sounds, or worse, breaking down. This is exactly why having maintenance rounds are especially important to any industrial machine being used to prevent machine faults.

Why do machines develop faults?

Corresponding to any other modern technology in the industry, machines also tend to deteriorate in time. Rapid deterioration usually comes into action when the device or rather, the machine is not well taken care of. That, and a hundred more reasons why your machine is experiencing mechanical faults. But here, we are letting you in on the four main reasons why your machine is malfunctioning.

Yes, there are probably numerous reasons why, but according to a study, these four main categories accept most of them. And here, we will be looking closely at these four categories that are consuming your machine’s health.

Four main causes of machine faults.

These are the most common causes of why your machine is acting up. We are covering four parts which are, misalignment, imbalance, looseness, and bearing time. In the reality of things, do not expect that these causes will be the only cause of machine destruction. As we have mentioned, there are numerous causes of why your machine is experiencing blunders. However, most of those errors are caused by these four things.

1 Machine faults: Misalignment

First, how, and why is this a machine fault? We will give you a straight answer. Misalignment can cause multiple disturbing things when the machine performs. Why? Because this kind of motor error is produced by excessive vibration, noise, coupling, bearing temperature increases, premature bearing, coupling, or shaft failure. Given all those things, machine misalignment is not that hard to miss.

Believe it or not, misalignment also has different types that you need to be aware of in order to fully understand the ins and outs of this categorical machine fault. Let us briefly break it down, shall we? There are three types of motor misalignment.

  • Angular Misalignment – Can cause severe damage to the driven equipment and other motors. This occurs when the motor is set at an angle to the driven equipment.
  • Parallel Misalignment – This occurs when the two shaft centerlines are parallel, but not in the same line.
  • Combination Misalignment – A combination of both parties above. This occurs when angular and parallel misalignment crosses paths, resulting in combination misalignment.

2 Machine faults: Looseness

At first thought, you might immediately think that something in the machine only needs tightening, but let us stop you right there. Looseness can be identified in three things and not just one. And there are levels of seriousness for each.

Type 1: This is when mechanical looseness has a time waveform of 1 pulse per revolution.

Type 2: This is caused by loose pillow block bolts, cracks in the frame structure, or in the bearing pedestal. The time waveform is typically two pulses per revolution.

Type 3: Deemed as the most complex one yet. According to a study, it is generally caused by the improper fit between components parts, such as bearings and their housing, a bearing liner loose in its cap, excessive clearance between a bearing and its sleeve, or a loose impeller on a shaft.

3 Mechanical faults: Imbalance

Also known as an unequal distribution of mass. According to a study by Lewis Motor Repair, balancing is a procedure in which the mass distribution of a rotor is assessed and if necessary, adjusted. Thus, when we say unbalanced, this simply means the unequal distribution of the weight of a rotor about its rotating centerline.

Here are some of the causes:

  • Blow Holes in Castings
  • Distortion
  • Corrosion or Wear
  • Deposit Build-Up
  • Manufactured Unsymmetrical Configurations
  • Hydraulic or Aerodynamic Unbalance

4 Mechanical faults: Bearing wear

It simply means that your mechanical motor is starting to get old. Ultimately, by carrying extensive loads, having poor lubrication or installation, the bearings will eventually fail. However, with the proper care and maintenance, such circumstances can be prevented.

Fluke Vibration Testers are the most ideal tool.

Get your hands on Fluke’s vibration testers. These test tools can undoubtedly be effective in every industrial operation whether it be an official check-up or your daily rounds. The Fluke 810 Vibration Tester is equipped with a diagnostic engine that combines algorithms with a database of real-world measurement experience. This device will allow them to quickly perform vibration analysis and evaluate the motor’s alignment accurately.

This will help every mechanical team in:

  • Prioritizing and planning repair activities and operating more efficiently.
  • Troubleshooting problem equipment and understanding the root cause of failure
  • Anticipate equipment failures before they happen.

Some of Fluke vibration tester’s prized qualities:

  • Comprehensive diagnostic reports and spectral diagrams help confirm data quality and narrow down the root cause of failures
  • Flexible machine speed configurations give the ability to test a broad range of assets including belt drives, gearboxes, and bevel gears
  • Fluke 810’s overall vibration level allows you to quickly assess overall machine health directly from the diagnosis screen
  • Accountability severity scale with four severity levels helps you prioritize maintenance work

Get your Fluke tool from a trusted source!

Presidium.PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools in the market!

Read more

Fluke Tools: How to Properly Clean Your Device

The growth of the pandemic has affected a lot of lives in terms of lifestyle and preventive health measures. New procedures were taken to ensure the safety of everyone. Most especially, new rules have been implemented to contain the spread of the virus. In lieu of this, one of the best practices everyone was taught was to keep our hands clean and disinfect gadgets.

With Fluke tools, no matter how rugged and durable fluke tools are, they are not susceptible to not inhabit any form of the virus.

With this said, now that society is slowly going back to normal, this doesn’t mean we should tolerate complacency. Normal processing of these health procedures should still be implemented especially in public places.

In an operational situation, or most especially, in work wherein touching things or being close to people is a must, hand hygiene, and device hygiene is a must. One of the most prominent working places that this usually happens is in industrial work areas.

Industrial work areas: What to expect?

Let’s just say working in the industrial sector is not a one-man job. Rather, it requires a lot of communication and teamwork. Furthermore, it also includes a lot of touching. Maybe not with your pals at work, but with your tools. And this can cause serious trouble to your workmates if one of the people touching that device is Covid positive. Scary right?

The passing of tools and data is not uncommon in a rugged environment. But to this day and age, it is also not deemed as the safest. Yes, the rates of Covid-19 cases have slowed down, but this doesn’t mean preventive measures should also slow down.

Caring for your Fluke tools.

Fluke tools are the best in the market, yes? Their reputation of being one of the most rugged tools in the industry is clear as daylight. This is why they are saturated by maintenance and troubleshooting professionals.

However, this doesn’t negate the fact that they also need a lot of caring and maintenance, specifically for the fact that they can be used in such harsh environments. Luckily for you, we’re here to show you how.

The role and importance of cleaning your devices.

According to WHO (World Health Organization), one of the most efficient ways how the virus jumps from one person to the next is in the form of touch. As stated by the University of Washington, cleaning removes most germs, as well as dirt and debris from surfaces or objects.

Ultimately, it was also mentioned in the study that the outer membrane of SARS-CoV-2, the virus that causes COVID-19, can be physically degraded by surfactants contained in all EPA-approved cleaning agents.

As you can see, properly cleaning your devices the proper way can boost workplace safety up a notch. Not only does this practice benefits your Fluke tools, but it also greatly benefits the people around you.

How you should properly clean Fluke tools.

To recall, the exterior of Fluke devices sports a yellow and grey hardcover. And with its ability to withstand harsh elements, let’s just say you shouldn’t go easy on it when you’re in the process of cleaning. Nevertheless, there is still a proper way to do it. Here’s how:

  • Use clean cloths – Really, if you’re going to use discarded scraps of old cloth, then why are we cleaning it in the first place? Using clean cloths can eliminate germs, bacteria, debris, dust, and dirt. On the other hand, if you’re using used cloths, then, there is a high chance you’re just spreading the dirt and not actually cleaning your device.
  • Use a Fluke Meter Cleaning wipe – Yes, ladies and gents, Fluke has an official cleaning wipe for its devices. It comes in a box and consists of black wipes. It is equipped with a pre-moistened industrial strength cleaning formula that removes surface dirt, oil, and grease from your test tools.
  • Dry your equipment after cleaning – Because let’s face it, every electronic thing on the planet whether it’s a high-end device or a state-of-the-art tech, each one of them hates water. They can tolerate yes, but initially, there’s a chance of cutting their lifespan short when they are exposed to any form of water.

Here’s what you shouldn’t do.

Now you know how to properly clean your Fluke test tools, now, we’ll show you what you shouldn’t do! Here are some of them:

  • Don’t use abrasive cleaners – These are scrubs, stones, liquid cleansers, powdered cleansers, etc. For the simple fact that it’s too strong of a cleaning solution for your device.
  • Do not immerse tools in liquid – Your Fluke tools might be dirtier than expected, but do not put them underwater. Stick to the wiping procedure above.

Get your Fluke tool from a trusted source!

Now that you know how to properly clean your Fluke tool, why not get them from a trusted distributor? Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fuke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools in the market!

Read more

Fluke Insulated Hand Tools: The Difference Between Regular Hand Tools and Insulated Hand Tools

One of the things that partner up well with cutting-edge Fluke devices is their Fluke Insulated Hand Tools. These are tools that should always be present in a maintenance professional’s belt. Fluke devices are tagged as one of the best in the market, for being effective, reliable, and with their iconic ruggedness. However, it wouldn’t hurt to have hand tools that can boost any professional’s performance.

Ultimately, Fluke devices give a quality performance in detecting faults. However, after issues with machines are detected, it is now the maintenance men at work who now hold the spotlight. When actual wire adjustments or issues with screws take place, this is where hand tools or insulated hand tools come in.

What are hand tools?

Once it is manually operated by hand that does not include any electricity, it is automatically considered as a hand tool. Every craftsman or a person who is fond of DIY projects should not be a stranger to these kinds of tools.

Basic hand tools used in construction or maintenance:

  • A set of pliers – Mostly used for maintenance purposes. These tools usually come as a set. Pliers are good for twisting wires, cutting wires, or gripping circular objects steadily.
  • Hammers – One of the popular tools in construction projects, they are usually used to hammer nails in place. They are used in projects such as assembling furniture, framing, shaping metals, and so on.
  • A set of screwdrivers – Similar with hammers, screwdrivers also put in screws. However, they don’t put it the same way a hammer does. Instead, they will put it in a turning moting to secure the screw.
  • Wrench – Can also come as a set. Wrenches are good for gripping, fastening, turning, tightening and loosening things like pipes, pipe fittings, nuts and bolts.
  • Saws – Preferrably made to cut out wood, metal, or stone because of its chisled edges.

These are usually the most basic hand tools that you would find in any handyman’s toolbox. Better yet, it is also the tools that we keep in storage in our homes in such cases when there’s a maintenance emergency.

There are two types of tools, a hand tool, and a power tool.

You must be wondering what’s the difference between them. It’s actually pretty simple. While hand tools rely on men to make them function, power tools come to life with the use of electricity. Power tools are considered to be the most advanced tools in the industry since they feature multiple functions in one tool. Moreover, they also save time and can produce outstanding results in return. Nevertheless, some professionals still opt to use trusty hand tools to get the job done.

Examples of power tools:

  • Power saws
  • Chainsaws
  • Power sanders
  • Power drills
  • Air compressor

Regular hand tools Vs. insulated hand tools.

We’ll get straight to the point. Yes, using insulated hand tools is much better than plain hand tools. But keep in mind that it will still depend on the hand tool’s usage and the project itself. In light of the usage of maintenance professionals, however, it will be beneficial for them to make use of insulated hand tools rather than plain ones. This is not because of the latest technology, but it’s actually for safety purposes.

Moreover, it is critical for a person working with electricity to know the difference between both since protecting yourself from possible hazardous voltages should be your number one priority. Genuine protection from electric shock goes beyond rubber slippers and personal protective equipment. So, if you have tools to help you be safe, better take advantage of them than be sorry.

In contrast, if you are not a maintenance professional and are only working on DIY projects that do not include encounters with live high voltage wires, a regular hand tool can already do the project justice.

Additionally, regular hand tools have nylon or plastic handles which cannot protect you from electric shocks if ever you encounter cutting live wires. On the other hand, Fluke Insulated Hand Tools are equipped to protect the man on the job if ever he encounters cutting live high voltage wires since it has electrical isolation on the handles.

Fluke insulated tools that should be in every maintenance man’s belt:

  • Diagonal cutter
  • Screwdriver kit
  • Pump pliers
  • Long nose plier
  • Combination pliers
  • Philip screwdriver (IPHS1 and IPHS2)

The importance and safety of using Fluke Insulated Hand Tools

It is undeniable that there are certain features that insulated hand tools have that regular one does not. And if you’re working in an environment where you are exposed to electricity on a daily basis, safety must be your number one priority. When dealing or working with live wires and high voltage electricity, your tools or devices will be your first line of defense.

Ultimately, the use of high-end devices should capture faults and issues in advance. Meanwhile, hand tools serve as the first contact with the troubled machine when it comes to troubleshooting. This is why when you ask every maintenance, HVAC, and utility professional, they would prefer to use insulated hand tools while performing their tasks.  

Notable safety measures of Fluke Insulated Hand Tools:

  • Have confidence in troubleshooting high voltage equipment without worrying about shocks.
  • Will reduce the possibility of arc faults caused by short circuits.
  • Can block potential hazardous voltages.
  • These tools underwent stringent testing to make sure tools are equipped to withstand hard use, extreme temperatures, and even live flame.
  • Designed to lessen strain and adapt to your hand.
  • Features a slim build that lets you easily access jammed junction boxes and panels.

The iconic Fluke reputation will truly exceed expectations. So, get yours now from a trusted distributor:

Read more

FieldSense Technology: Creating A Safer Way for Simultaneous Voltage and Current Measurements

Working on electrical wiring and high voltages can be a hazardous undertaking. Although there are preventive measures that one can implement (such as PPE’s and insulated tools) this can only do the bare minimum when you’re under electrical dangers. Luckily, with the innovations of technology, maintenance workers can be more at ease when doing high-risk rounds. By using the new and improved FieldSense technology it can guarantee more safety for the men at work. Its improved functions can attest to this.

However, maintenance professionals are aware of the risks and have undergone preventive training. It’s always preferable to work with tools that can ensure safety and can do the job right. And Fluke tools have just about every unit of these safe and efficient devices that is every maintenance man’s dream tool.

What is FieldSense Technology?

In simple terms, FiledSense Technology is the new and improved way of measuring simultaneous voltage and currents. Basically, the traditional way of measuring such risky parts of a machine or panels is by poking and touching certain parts of the machine that can endanger a man at work. 

However, with the use of FieldSense Technology, it has the capacity to eliminate more risks. Initially, the old way of measuring this is by being in contact with electrical conductors with the use of test leads. This method requires metal-to-metal contact that may carry potential arc flash or electrical shock.

But then again, with the use of this advanced tool, it’s one worry of maintenance and troubleshooting men that they can finally be at peace with.

Safe measurements using FieldSense Technology.

We’re running down facts on how using FieldSense Technology can benefit you on the field. Ultimately, workers (such as commercial and industrial electricians) can use Fieldsense technology for voltage and current measurements, verifying continuity values, and testing individual circuits. However, there is more to this device than just those previously stated.

Aside from its amazing functions, these are some of the things on how this devi9ce can benefit any maintenance or troubleshooting professional on the field.

An option of no metal-to-metal contact

One of the greatest and most favored functions of FieldSense Technology is its ability to measure without metal contact. Unlike most devices that need test probes or alligator clips that need to be connected to the conductor to get accurate readings, FieldSense technology does not require those technicalities.

Basically, in doing so, you are also putting your safety at risk since these kinds of procedures may trigger sparks, arc flashes, or electric shock.

However, by using the new and advanced Fluke FieldSense Technology, you can put yourself at ease since it doesn’t require any contact. This technology allows you to measure ac voltage, current, and frequency through the cable’s insulation by sliding the fork of the tester over the conductor. Therefore, there will be no direct electrical contact with live voltage lessening the risks of dire circumstances.

FieldSense Technology offers more than fault detection.

There will be no shortage of devices that can measure voltage and Fluke tools are one of them. Being recognized as one of the best test tools in the market, Fluke innovates devices to further meet the needs of workers in this continuously advancing world. With this said, Fluke FieldSense offers this kind of innovation by going beyond voltage detection.

Ultimately, this device can also offer to accurately measure the given voltage. Basically, by having this device in your back pocket, you now have voltage detection and a measurement tool, all in one device! Sounds great? There’s more coming! 

FieldSense technology can reduce the need to open panels.

Fluke FieldSense is also known for its fast and easy measurement methods. One of the ways that this device is tagged as a quick measurement tool is because it doesn’t really require you to open any panels. Have the ease to take measurements at any point along the conductor. Technically, you only need to slide its fork-like top to one of the single conducting wires and read the results. Easy and one, two, three!

Take measurements without fussing.

No need to worry about test leads or probes with this one. And when we say you no longer need them, we mean it! FiledSense can still accurately measure voltage without them. What’s cool? Because you no longer need additional accessories for this one, you can have the ability to multitask. Have your FieldSense technology on one hand while doing other priorities on the other.

Its fork-like top can give you the ease of isolating individual hot and neutral wires which in turn helps reduce the chance of accidental contact with another voltage point and the likelihood of errors. Save more time and accomplish more things with this little device!

It promotes proper operation.

Initially, when you’re about to operate on something using any Fluke device a rule of thumb before each operation is making sure that the FLuke device is working smoothly before undergoing any tests. In as much, the FieldSense technology makes sure of this. If you’re a newbie on the field have the habit of testing your device before and after living tests to ensure security and more accurate measurements.   

Get your Fluke tool from a trusted source!

Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop shop for the best test tools in the market!

Read more

Laser Distance Meter 101: Important Facts You Should Know About!

Laser distance meters are extra than just for measurement. We’re talking about innovative tools that can support you in taking precise measurements while also securing a worker’s safety. Laser distance meters take measurement into the modern world wherein you no longer need bulky reel-in tapes or walking wheel distance measurement systems.

What’s new with measurement?

Traditional measurement requires physical contact to know the distance of one point to the other. However, with a laser distance meter, you can achieve accuracy in determining these lengths without contact. In the name itself “laser” this device uses a laser to accurately determine long distances.

Thus laser distance meters are popularly used in different industrial sectors. Here are some of them:

  • Carpentry
  • Masonry
  • Electrical
  • Landscapers
  • Developers
  • Locksmiths

These devices are mostly used but not limited to these types of industries. Then again, one must think, there’s always the trusty and handy measuring tapes which are more affordable so why not use that?

Why you should use a Fluke Laser Distance Meter.

Other than the fact that this product hailed from one of the most distinguished brands for test tools, here are some reasons why you should opt to use a laser distance meter:

  • It’s faster – Point and click! You’ll have results in no time. You’ll get the job done within seconds compared to using a regular tape which eats a lot of minutes just by unrolling it. Not to mention, the use of additional people for you to guarantee accurate results.
  • You don’t need to walk – Unlike regular tape measures which need a lot of movement and effort, laser distance meters only require you to hold one spot in the field and point in the direction you want to measure. Fewer hassles right? 
  • Use it even with poor lighting – The thing with tape measures (or any kind of non-digital measure tool) is that it might be difficult to take data at night or with low lights in general. In totality, the person conducting the measurement might have a hard time navigating in the dark as well. However, with the use of laser distance meters, be able to take measurements more efficiently because of its backlit display.
  • No contact is needed! – You no longer need to poke, jab, or worry about ground obstacles. All you need to do is point it in the right direction and you’ll get the results you need.
  • Measure in all directions even upwards – The most popular measurement we make is the one across something (length or width of something). One downside of using tape is sometimes, it’s not enough in terms of material. But, by using laser distance meters, be confident by measuring in all different directions (across, above, below, sideways, etc.) without moving an inch.  
  • Safety and versatility – You can’t deny the valuable features of the Fluke laser distance meter especially when you’re working in a hazardous environment. Because of its advanced features, workers will no longer undertake risks.

Different applications of laser distance meter.

As we’ve mentioned above, laser distance meters are popular with industrial use but not limited to them. On the contrary, you can actually use this device in a wide variety of things. Here are some of them:

In facilities

  1. Use the laser distance meter in setting up floor supports in large rooms.
  2. Can be used to measure room dimensions to calculate how much paint is needed.
  3. Measure room dimensions to calculate how much floor covering is needed.
  4. Measure height for appropriate ladder selection.
  5. Document the location of standing water or leaks found with a thermal imager or infrared

Measure walls and ceilings

  1. Calculate distances to objects within hard-to-reach drop ceilings to determine overhead cable runs, line of sight.
  2. Measure ceiling height and square feet/meters to determine rod lengths for drop ceiling installation and lighting fixtures.
  3. Measure distance under subfloors or structures for networking or other cable installations.

Safety purposes

  1. Measure distances (including ceiling heights) to install emergency lighting, sprinklers, and fire extinguishers to code.
  2. Determine accurate room dimensions to ensure correct chemical concentration for Clean Agent Fire Suppression system.
  3. Measure distances from machines for safety equipment (fire extinguishers, fire blankets, etc.).

Great features, great performance.

The best Fluke laser distance meters come in two units which are the Fluke 424D Laser Distance Meter and Fluke 417 Laser Distance Meter. Let’s take a closer look at each of them.

Fluke 424 Laser Distance Meter.

This unit is tagged as the most sophisticated measuring tool in the market. It can instantly measure up to 100 meters (330 ft). This unit also features a bright pointer laser that supports laser targeting even at longer distances. Not only that, but the backlit display is also a winning feature of this unit. With its advanced functions, you can ultimately have enough uptime for two people combined.

Fluke 417 Laser Distance Meter.

This unit features durability, accuracy, and ease of use. Designed for both outdoor and indoor use, this will allow you to minimize time spent measuring and maximize the reliability of measurements. This unit also showcases a backlit display and a laser pointer for accurate measurement.

Get your Fluke tool from a trusted source!

Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fuke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools in the market!

Fluke Laser Distance Meter: https://presidium.ph/?s=laser+distance+meter

Read more

Fluke Test Tools: Recommended Battery Testing to Ensure Optimal Uptime

One of the most important parts of every device is its batteries. Professionals in the industry even advise making rounds on batteries to make sure their performance is at a hundred percent. Although batteries today, are evidently more advanced than the ones before and are often tagged as low maintenance, this doesn’t mean that they should be dismissed. Battery testing is one of the musts that every maintenance man/woman should practice. Ultimately, with the help of Fluke test tools, these devices can ensure battery health with a click of a button.

In light of battery kinds, the most popularly used are the uninterrupted power supply (UPS) and battery backup systems. Again, these types of batteries also hold a reputation for being maintenance-free. However, like all things, in time, these batteries are also susceptible to deteriorate over time. Not only that, but they are also prone to corrosion, internal shorts, sulphation, dry out, and seal failure. And when these issues occur, it will result in frustrating downtimes. 

Determining battery failure.

Voltage usually plays a big role in determining battery health. But, the question remains, is it enough? The answer is no. We’re not saying it’s wrong, but you can do more to ensure that your batteries are in a good state.

In totality, measuring voltage is only the tip of the iceberg. Online monitoring equipment or in-person voltage tests won’t give you the full picture of your battery’s health. This is because the voltage is an indication of your battery’s state of charge and not your battery’s health.

To make it clear, the measuring voltage will not tell you beforehand if your battery is degrading. In line with this, voltage testing also has a drawback when a load is applied.

A recommended approach to battery testing.

Instead of relying on voltage testing, try measuring battery impedance as well. In this way, you’ll have a better understanding of the internal resistance of the battery and not just its state of charge. Basically, if you measure battery impedance, this will give you a whole picture of your battery’s issues.

What is battery impedance and why is it preferred?

Battery impedance is made up of two components. Those are electrical and ohmic resistance. Let’s break them down! First, electrical resistance deals with the current flow in an electrical circuit. Meanwhile, ionic resistance measures current flow due to internal factors such as electrode surface area and electrolyte conductivity.

On the other hand, internal ohmic values or also known as the AC resistance can be a big factor in determining the battery’s overall health. AC resistance can be measured by injecting a small current and then later on calculated using Ohm’s law. But in this case, you might want to consider Fluke test tools for easier and more convenient results.

Measuring battery impedance.

Unlike voltage testing, measuring the impedance values can help you detect potential battery problems in advance. In time, a battery’s internal resistance can increase and when this happens, it means that the battery itself is already on the verge of degradation in the cell.     

The best practice for measuring battery impedance. You must be consistent. A single measurement cannot dictate the entire context of what is happening or what is about to happen with your batteries. Make it a habit to measure impedance over months and years. It also helps to examine changes and don’t forget to put it on record every time you make measurements.

Fluke Test Tools: Fluke Battery Analyzer

The best tool to measure battery impedance is none other than Fluke test tools! Specifically, the Fluke Battery Analyzer. This is the ideal fluke test tool for maintenance, troubleshooting, and performance testing of individual stationary batteries and battery banks used in critical battery backup applications.

As we’ve discussed, one of the key points that need to be measured is internal battery resistance, dc and ac voltage, dc and ac current, ripple voltage, frequency, and temperature. With the Fluke Battery Analyzer, you can measure all of these components with just one tool making it a great investment for long-term use!

Get your Fluke tool from a trusted source!

Presidium PH is an authorized distributor of Fluke test tools in the Philippines. So, if you want to know more about Fuke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools in the market! (insert website link battery analyzer)

Read more

Fluke Thermometers: How to Get the Best Results!

There is no tool timelier than a Fluke thermometer during the surge of a pandemic. When we are limited to giving physical touch while working, we turn to instruments that can do the job for us. Fluke thermometers are not only supportive of diagnosing technical issues but are also capable of doing thorough temperature reads of different objects. However, this may also vary from the actual object you are measuring.

Recap! A lot of people mistake IR Thermometers for Thermal Imagers. So, what’s the difference? A simple explanation that sets these two fluke devices apart is that Fluke thermometers take an individual number which is the temperature measurement of a single spot on your target. Meanwhile, a thermal camera gives you thermal readings that let you visualize the actual hot and cold spots scenario.

Going back, it’s safe to say that it’s in everyone’s knowledge, Fluke thermometers are great in terms of performance! However, some might not be getting the full experience of these innovative thermometers. This is why we’re telling you how you can get the best results from Fluke thermometers!

Know your IR thermometer’s distance-to-spot ratio

The distance-to-spot ratio is known as the field of view. The field of view plays a critical role in terms of accuracy. This is because the angle of vision it sees will be the average of the temperature it detects.

Additionally, the distance-to-spot ratio also pertains to the size of the area (or spot) being measured. Make sure that the target is larger than the spot size the unit is measuring. The smaller the target, the closer you should be to it. When accuracy is critical, make sure that the target is at least twice as large as the spot size.

Watch out for shiny, “low emissivity” objects.

Yes, shiny objects have the tendency to bewilder your IR gun which as a result can give inaccurate results. According to EnnoLogic, IR thermometers are pre-set at an emissivity of 0.95.  However, objects with much lower emissivity ratings, such as polished metal, will give false temperature readings.

Another source from Thermo Works stated that most organic materials, including the by-products of plants and animals, have an emissivity rating of 0.95. In return, these are the ideal surfaces to point at if you want accurate results. Meanwhile, polished metals and other shiny things are known to have very low emissivity levels since they tend to be very reflective of ambient infrared energy.

Steam or dust can affect the accuracy of IR thermometers.

Remember that these elements can confuse readings for the simple reason that they blur the lens. Naturally, blurry lenses can result in inaccurate readings for infrared thermometers. Think of it this way, if you look through a camera with blurred lenses or steam, those elements will show in the photos. Therefore, before shooting your IR gun, always make sure to wipe the lenses with appropriate tools to better its reading process.

Avoid temperature-shocking your infrared thermometer.

We know that Fluke is known for its excellence of being the most versatile test tool in the market, and it’s not wrong. However, some of its tools are also quite sensitive depending on their usage. Nevertheless, don’t mistake this aspect as a weak spot since this does not dampen its high-performing nature.

Letting your Fluke thermometer simmer in its surroundings can ultimately grant you more chances to get accurate readings. Give your thermometer at least 20 minutes to bask in its given environment. For example, you’ve just only done temperature checks in a cold room and then moved on to a much warmer area. Immediately putting your device on the spot might not get you the most “spot-on” results, instead, let it sit and take in the surrounding for a minimum of 20 minutes.

Get your Fluke tool from a trusted source!

Presidium PH is an authorized distributor of Fluke Maintenance tools in the Philippines. Thus, if you want to know more about Fluke tools and their functions, visit our website for more info! This is a one-stop-shop for the best test tools in the market!

Read more